BeamZ Butterfly II 153.713 Handleiding

BeamZ Effect machine Butterfly II 153.713

Lees hieronder de 📖 handleiding in het Nederlandse voor BeamZ Butterfly II 153.713 (10 pagina's) in de categorie Effect machine. Deze handleiding was nuttig voor 33 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/10

Buttery II 6x3W RGBAWP IR

Ref. nr.: 153.713

INSTRUCTION MANUAL

GEBRUIKSAANWIJZING

GEBRAUCHSANLEITUNG

MANUAL DE INSTRUCCIONES

MANUEL D'INSTRUCTIONS

V1.1

ENGLISH

Congratulations to the purchase of this Beamz xture. Please read this manual thoroughly prior to using the unit in order to

benet fully from all features.

Read the manual prior to using the unit. Follow the instructions in order not to invalidate the warranty. Take all precautions to

avoid re and/or electrical shock. Repairs must only be carried out by a qualied technician in order to avoid electrical shock.

Keep the manual for future reference.

- Prior to using the unit, please ask advice from a

specialist. When the unit is switched on for the rst time,

some smell may occur. This is normal and will disappear

after a while.

- The unit contains voltage carrying parts. Therefore do

NOT open the housing.

- Do not place metal objects or pour liquids into the unit

This may cause electrical shock and malfunction.

- Do not place the unit near heat sources such as

radiators, etc. Do not place the unit on a vibrating

surface. Do not cover the ventilation holes.

- The unit is not suitable for continuous use.

- Be careful with the mains lead and do not damage it. A

faulty or damaged mains lead can cause electrical shock

and malfunction.

- When unplugging the unit from a mains outlet, always

pull the plug, never the lead.

- Do not plug or unplug the unit with wet hands.

- If the plug and/or the mains lead are damaged, they

need to be replaced by a qualied technician.

- If the unit is damaged to such an extent that internal

parts are visible, do NOT plug the unit into a mains outlet

and DO NOT switch the unit on. Contact your dealer. Do

NOT connect the unit to a rheostat or dimmer.

- To avoid re and shock hazard, do not expose the unit to

rain and moisture.

- All repairs should be carried out by a qualied technician

only.

- Connect the unit to an earthed mains outlet (220-

240Vac/50Hz) protected by a 10-16A fuse.

- During a thunderstorm or if the unit will not be used for a

longer period of time, unplug it from the mains. The rule

is: Unplug it from the mains when not in use.

- If the unit has not been used for a longer period of time,

condensation may occur. Let the unit reach room

temperature before you switch it on. Never use the unit in

humid rooms or outdoors.

- During operation, the housing becomes very hot. Do not

touch it during operation and immediately after.

- To prevent accidents in companies, you must follow the

applicable guide lines and follow the instruction s.

- Secure the unit with an extra safety chain if the unit is

ceiling mount. Use a truss system with clamps. Make

sure nobody stands in the mounting area. Mount the

eect at least 50cm away from inammable material and

leave at least 1 meter space on every side to ensure

sucient cooling.

- This unit contains high intensity LEDs. Do not look into

the LED light to prevent damage to your eyes.

- Do not repeatedly switch the xture on and o. This

shortens the life time.

- Keep the unit out of the reach of children. Do not leave

the unit unattended.

- Do not use cleaning sprays to clean switches. The

residues of these sprays cause deposits of dust and

grease. In case of malfunction, always seek advice from

a specialist.

- Only operate the unit with clean hands.

- Do not force the controls.

- If the unit has fallen, always have it checked by a

qualied technician before you switch the unit on again.

- Do not use chemicals to clean the unit. They damage the

varnish. Only clean the unit with a dry cloth.

- Keep away from electronic equipment that may cause

interference.

- Only use original spares for repairs, otherwise serious

damage and/or dangerous radiation may occur.

- Switch the unit o prior to unplugging it from the mains

and/or other equipment. Unplug all leads and cables

prior to moving the unit.

- Make sure that the mains lead cannot be damaged when

people walk on it. Check the mains lead before every use

for damages and faults!

- The mains voltage is 220-240Vac/50Hz. Check if power

outlet match. If you travel, make sure that the mains

voltage of the country is suitable for this unit.

- Keep the original packing material so that you can

transport the unit in safe conditions

This mark attracts the attention of the user to high voltages that are present inside the housing and that are of sucient

magnitude to cause a shock hazard.

This mark attracts the attention of the user to important instructions that are contained in the manual and that he should

read and adhere to.

DO NOT LOOK DIRECTLY INTO THE LENS. This can damage your eyes. Persons who are subject to epileptic attacks

should be aware of the eects that this light eect may have on them.

The unit has been certied CE. It is prohibited to make any changes to the unit. They would invalidate the CE certicate and

their guarantee!

NOTE: To make sure that the unit will function normally, it must be used in rooms with a temperature between 5°C/ °F 41 and

35 95°C/ °F.

Electric products must not be put into household waste. Please bring them to a recycling centre. Ask your local authorities or your

dealer about the way to proceed. The specications are typical. The actual values can slightly change from one unit to the other.

Specications can be changed without prior notice.

UNPACKING INSTRUCTION

CAUTION! Immediately upon receiving a xture, carefully unpack the carton, check the contents to ensure that all parts are

present, and have been received in good condition. Notify the shipper immediately and retain packing material for inspection if

any parts appear damage from shipping or the package itself shows signs of mishandling. Save the package and all packing

materials. In the event that a xture must be returned to the factory, it is important that the xture be returned in the original

factory box and packing.

If the device has been exposed to drastic temperature uctuation (e.g. after transportation), do not switch it on immediately. The

arising condensation water might damage your device. Leave the device switched o until it has reached room temperature.

POWERSUPPLY

On the label on the backside of the xture is indicated on this type of power supply must be connected. Check that the mains

voltage corresponds to this, all other voltages than specied, the light eect can be irreparably damaged. The xture must also

be directly connected to the mains and may be used. No dimmer or adjustable power supply.

Always connect the xture to a protected circuit (circuit breaker or fuse). Make sure the xture has an appropriate

electrical ground to avoid the risk of electrocution or re.

INSTALLATION

Attention:

 The installation of the fixture has to be built and constructed in a way that it can hold 10 times the weight

for 1 hour without any harming deformation.

 The installation must always be secured with a secondary safety attachment, e.g. an appropriate catch net.

This secondary safety attachment must be constructed in a way that no part of the installation can fall down

if the main attachment fails.

 Make sure the area below the installation place is free from unwanted persons during rigging, de-rigging

and servicing.

 The operator has to make sure that safety-relating and machine-technical installations are approved by an

expert before taking into operation for the first time and after changes before taking into operation another

time.

 The operator has to make sure that safety-relating and machine-technical installations are approved by a

skilled person once a year.

 The xture should be installed in the position where persons cannot reach and where persons may walk by

or be seated.

CAUTION: Please consider the respective national norms during the

installation! The installation must only be carried out by an

authorized employee or dealers!

CAUTION: When installing the xture, make sure there is no highly in

inammable material (decoration articles, etc.) in between a

distance of min 0.5 meter.

Product specificaties

Merk:	BeamZ
Categorie:	Effect machine
Model:	Butterfly II 153.713
Kleur van het product:	Zwart
Gewicht:	1600 g
Breedte:	185 mm
Diepte:	205 mm
Hoogte:	190 mm
Aantal lampen:	6 lampen
Soort lamp:	LED
Vermogen lamp:	3 W
Stroombron:	AC
Ingangsspanning:	100-240 V
Frequentie:	50/60 Hz
Stroomverbruik (typisch):	20 W
Type product:	Discostroboscoop
Baldiameter:	- "