Atlas Sound FAP42T-W Handleiding

Atlas Sound Speaker FAP42T-W

Lees hieronder de 📖 handleiding in het Nederlandse voor Atlas Sound FAP42T-W (1 pagina's) in de categorie Speaker. Deze handleiding was nuttig voor 35 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/1
Ceiling Material up to 2"
Tile
Bridge
xillaryAu
Suspension
Point
Dog Leg
In Inverted
Position
Ceiling Material up to 11
/
4"
Tile
Bridge
Auxillary
Suspension
Point
Dog Leg
In Normal
Position
FAP42T
Installation
Instructions
ATS001131a RevF 12/08
FAP42T
Installation Instructions
Mounting Template
9" Dia.
The Atlas Sound Strategy Series
® II assembly mounts easily into existing
construction drop ceiling or drywall materials
Painting Shield
812" Dia.
Drop Tile Ceiling
Installation
1. Remove 2'x2' or 2'x4' tile.
2. Align adjustable dual rail c-ring assembly on rear of tile in desired position.&
3. Using template provided mark cutout circle with marker and cut hole. (9" FAP42T)
4. Affix C-ring assembly to rails using screws provided and position assembly on rear of ceiling
tile. Replace tile into grid making sure that formed ends of tile bridge rails engage T-bar tile support rails.
5. Bring service loop from rear of tile, through tile bridge C-ring to access panel located on side of
enclosure. Terminate the service loop to Phoenix style connector provided (please note polarity). Combination
knockouts are provided to facilitate conduit.
6. Insert enclosure through front of tile. Using standard #2 Phillips screwdriver or screw-gun, tighten (4) dogleg
assemblies until they engage C-ring assembly. DO NOT OVER-TIGHTEN DOG LEG SCREWS!
7. Adjust front mounted switch to desired wattage tap setting or 8Ω* (See important note regarding 8 operation)Ω
8. Install press-fit grille into front bezel ring. Push baffle upwards until baffle is flush with bezel ring.
9. For safety and seismic considerations a suspension ring is integrated into input panel section of unit. Atlas Sound strongly suggests
that a support wire be installed from this support point to a suitable anchor point above ceiling grid. In drop tile applications, this wire
can usually be installed from an adjacent tile access near speaker location.
Dry Wall ("Hard Deck") Installation
1. Using template provided, mark cutout circle in desired mounting location and cut hole. (9" FAP42T)
2. Place tile bridge rails and C-ring through hole. Use V shaped edge of C-ring to align tile bridge assembly above ceiling (alignment screws
provided are not required for this type of installation)
3. Bring service loop from through the tile bridge/C-ring to access panel located on side of the enclosure. Terminate service loop to Phoenix style
connector provided (please note polarity). Combination knockouts are provided to facilitate conduit.
4. Insert enclosure into hole. Using standard #2 Phillips screwdriver or screw-gun, tighten (4) dogleg assemblies until they engage the C-ring assembly.
DO NOT OVER-TIGHTEN DOG LEG SCREWS!
5. Adjust front mounted switch to desired wattage tap setting or 8Ω* (See important note regarding 8 operation)Ω
6. Install press-fit grille into front bezel ring. Push baffle upwards until baffle is flush with bezel ring.
New Construction (Darywall Ceilings)
Use of optional FAP42-TR1 (for use with FAP42T) new construction bracket essentially reserves speaker mounting location prior to drywall installation
in new construction. Bracket mounts between 16" or 24" OC studs and includes a 3/8" downward lip to provide a template for drywall installers to cut
around. For final installation, please follow instructions below.
Note: tile bridge components are not used in new construction applications where new construction bracket is utilized.
1. Bring service loop through hole in ceiling provided by pre construction bracket to access panel located on side of Enclosure.
Terminate service loop to Phoenix style connector provided (please note polarity). Combination knockouts are provided to facilitate conduit.
2. Insert speaker assembly into hole. Using standard #2 Phillips screwdriver or screw-gun, tighten (4) dog leg assemblies until they engage
ring provided on new construction bracket. DO NOT OVER-TIGHTEN DOG LEG SCREWS!
3. Adjust front mounted switch to desired wattage tap setting or 8Ω* (See important note regarding 8 operation)Ω
4. Install press-fit grille into front bezel ring. Push baffle upwards until baffle is flush with bezel ring.
ATS001131a RevD 2/04
Typical rallel Hookup of Full nge 70.7/100V SpeakersPa Ra
1 2 3 4 5 6 master po wer
po wer
Input
+
-
Typical 120Watt 70.7V Output
Tap ttage tal 64 ttsWa To : Wa
Amplifier
FAP42T
16W @ 70.7V
Full ngeRaFull ngeRaFull ngeRa
16W @ 70.7V16W @ 70.7V
FAP42T
-+
FAP42T
+ - +
Full ngeRa
16W @ 70.7V
FAP42T
- + -
1 FAP42-TR Has not been evaluated by UL Laboratories
NOTE: Dog legs will accommodate ceiling material thickness up to 1 1/4" as shipped from factory.
For thicker ceiling materials (up to 2") simply unscrew and flip dog legs as shown.
DO NOT OVER-TIGHTEN DOG LEGS IN EITHER CONFIGURATION!
NOTE: UL recognized conduit clamp must be used for conduit
connections. Cable connection cavity is not intended to be used
as a junction box.
FREQUENCY RESPONSE: 70Hz-20kHz SENSITIVITY: 88dB (1W/1M)
NOTE: *DO NOT USE 8Ω SETTING WITH 70.7V/100V SYSTEMS! *DO NOT
OVERPOWER IN 8 CONFIGURATION! AMPLIFIER OUTPUT SHOULD NOT Ω
EXCEED 16W RMS @ 8 PER SPEAKERΩ


Product specificaties

Merk: Atlas Sound
Categorie: Speaker
Model: FAP42T-W

Heb je hulp nodig?

Als je hulp nodig hebt met Atlas Sound FAP42T-W stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Speaker Atlas Sound

Handleiding Speaker

Nieuwste handleidingen voor Speaker