Asrock AM1B-ITX Handleiding

Asrock Moederbord AM1B-ITX

Lees hieronder de 📖 handleiding in het Nederlandse voor Asrock AM1B-ITX (60 pagina's) in de categorie Moederbord. Deze handleiding was nuttig voor 10 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/60

User Manual

Version 1.1

Published October 2014

No part of this documentation may be reproduced, transcribed, transmitted, or

translated in any language, in any form or by any means, except duplication of

documentation by the purchaser for backup purpose, without written consent of

ASRock Inc.

Products and corporate names appearing in this documentation may or may not

be registered trademarks or copyrights of their respective companies, and are used

only for identication or explanation and to the owners’ benet, without intent to

infringe.

Disclaimer:

Specications and information contained in this documentation are furnished for

informational use only and subject to change without notice, and should not be

constructed as a commitment by ASRock. ASRock assumes no responsibility for

any errors or omissions that may appear in this documentation.

With respect to the contents of this documentation, ASRock does not provide

warranty of any kind, either expressed or implied, including but not limited to

the implied warranties or conditions of merchantability or tness for a particular

purpose.

In no event shall ASRock, its directors, ocers, employees, or agents be liable for

any indirect, special, incidental, or consequential damages (including damages for

loss of prots, loss of business, loss of data, interruption of business and the like),

even if ASRock has been advised of the possibility of such damages arising from any

defect or error in the documentation or product.

e terms HDMI™ and HDMI High-Denition Multimedia Interface, and the HDMI

logo are trademarks or registered trademarks of HDMI Licensing LLC in the United

States and other countries.

is device complies with Part 15 of the FCC Rules. Operation is subject to the following

two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

CALIFORNIA, USA ONLY

e Lithium battery adopted on this motherboard contains Perchlorate, a toxic substance

controlled in Perchlorate Best Management Practices (BMP) regulations passed by the

California Legislature. When you discard the Lithium battery in California, USA, please

follow the related regulations in advance.

“Perchlorate Material-special handling may apply, see

www.dtsc.ca.gov/hazardouswaste/perchlorate”

ASRock Website: http://www.asrock.com

Contents

Chapter 1 Introduction 1

1.1 Package Contents 1

1.2 Specications 2

1.3 Unique Features 6

1.4 Motherboard Layout 9

1.5 I/O Panel 11

Chapter 2 Installation 12

2.1 Installing the CPU 13

2.2 Installing the CPU Fan and Heatsink 15

2.3 Installing Memory Modules (DIMM) 16

2.4 Expansion Slots (PCI Express Slots) 18

2.5 Jumpers Setup 19

2.6 Onboard Headers and Connectors 20

Chapter 3 Software and Utilities Operation 24

3.1 Installing Drivers 24

3.2 A-Tuning 25

3.3 Start8 28

Chapter 4 UEFI SETUP UTILITY 31

4.1 Introduction 31

4.1.1 UEFI Menu Bar 31

4.1.2 Navigation Keys 32

4.2 Main Screen 33

4.3 OC Tweaker Screen 34

4.4 Advanced Screen 37

4.4.1 CPU Conguration 38

4.4.2 Chipset Conguration 39

4.4.3 Storage Conguration 41

4.4.4 Super IO Conguration 42

4.4.5 ACPI Conguration 43

4.4.6 USB Conguration 45

4.4.7 Trusted Computing 46

4.5 Tools 47

4.6 Hardware Health Event Monitoring Screen 50

4.7 Boot Screen 51

4.8 Security Screen 54

4.9 Exit Screen 55

AM1B-ITX

English

Chapter 1 Introduction

ank you for purchasing ASRock AM1B-ITX motherboard, a reliable motherboard

produced under ASRock’s consistently stringent quality control. It delivers excellent

performance with robust design conforming to ASRock’s commitment to quality

and endurance.

In this manual, Chapter 1 and 2 contains the introduction of the motherboard

and step-by-step installation guides. Chapter 3 contains the operation guide of the

soware and utilities. Chapter 4 contains the conguration guide of the BIOS setup.

1.1 Package Contents

ASRock AM1B-ITX Motherboard (Mini-ITX Form Factor)

ASRock AM1B-ITX Quick Installation Guide

ASRock AM1B-ITX Support CD

2 x Serial ATA (SATA) Data Cables (Optional)

1 x I/O Panel Shield

Because the motherboard specications and the BIOS soware might be updated, the

content of this manual will be subject to change without notice. In case any modica-

tions of this manual occur, the updated version will be available on ASRock’s website

without further notice. If you require technical support related to this motherboard,

please visit our website for specic information about the model you are using. You

may nd the latest VGA cards and CPU support list on ASRock’s website as well.

ASRock website http://www.asrock.com.

English

1.2 Specications

Platform Mini-ITX Form Factor

All Solid Capacitor design

CPU Supports AMD AM1 Socket A-series and E-series Quad-

Core/Dual-Core APU up to 25W

Memory 2 x DDR3 DIMM Slots

Supports DDR3 1600/1333/1066 non-ECC, un-buered

memory

Max. capacity of system memory: GB (see CAUTION1)32

Expansion

Slot

1 x PCI Express 2.0 x16 Slot (PCIE1 @ p6-x4 mode)

Graphics Integrated AMD RadeonTM R3 Series Graphics in A-series /

E-series APU

DirectX 11.1, Pixel Shader 5.0

Max. shared memory GB2

ree graphics output options: D-Sub, DVI-D and HDMI

Supports HDMI with max. resolution up to 4K × 2K

(4096x2160) @ 24Hz or 4K × 2K (3840x2160) @ 30Hz

Supports DVI-D with max. resolution up to 1920x1200 @

60Hz

Supports D-Sub with max. resolution up to 2048x1536 @

60Hz

Supports Auto Lip Sync, Deep Color (12bpc), xvYCC and

HBR (High Bit Rate Audio) with HDMI Port (Compliant

HDMI monitor is required)

Supports HDCP with DVI-D and HDMI Ports

Supports Full HD 1080p Blu-ray (BD) playback with DVI-D

and HDMI Ports

Audio 5.1 CH HD Audio (Realtek ALC662 Audio Codec)

Supports Full Spike Protection

AM1B-ITX

English

LAN PCIE p7-x1 Gigabit LAN 10/100/1000 Mb/s

Realtek RTL8111GR

Supports Realtek RealWoW! Technology

Supports Wake-On-LAN

Supports Full Spike Protection

Supports LAN Cable Detection

Supports Energy Ecient Ethernet 802.3az

Supports PXE

Rear Panel

I/O

1 x PS/2 Mouse/Keyboard Port

1 x Parallel Port (ECP/EPP support)

1 x D-Sub Port

1 x DVI-D Port

1 x HDMI Port

2 x USB 2.0 Ports (Supports Full Spike Protection)

2 x USB 3.0 Ports (Supports Full Spike Protection)

1 x RJ-45 LAN Port with LED (ACT/LINK LED and SPEED

LED)

HD Audio Jacks: Line in / Front Speaker / Microphone

Storage 2 x SATA3 6.0 Gb/s Connectors by AMD AM1 Series Socket

25W Quad-Core APU, support NCQ, AHCI and Hot Plug

2 x SATA3 6.0 Gb/s Connectors by ASMedia ASM1061, sup-

port NCQ, AHCI and Hot Plug

Connector 1 x COM Port Header

1 x Chassis Intrusion Header

1 x TPM Header

1 x CPU Fan Connector (4-pin)

1 x Chassis Fan Connector (4-pin)

1 x Power Fan Connector (3-pin)

1 x 24 pin ATX Power Connector

1 x Front Panel Audio Connector

2 x USB 2.0 Headers (Support 4 USB 2.0 ports) (Supports Full

Spike Protection)

1 x USB 3.0 Header by ASMedia ASM1042A (Supports 2 USB

3.0 ports) (Supports Full Spike Protection)

English

BIOS

Feature

32Mb AMI UEFI Legal BIOS with GUI support

Supports “Plug and Play”

ACPI 1.1 compliance wake up events

Supports jumperfree

SMBIOS 2.3.1 support

DRAM Voltage multi-adjustment

Support

Drivers, Utilities, AntiVirus Soware (Trial Version), Google

Chrome Browser and Toolbar, Start8 (30 days trial)

Hardware

Monitor

CPU/Chassis temperature sensing

CPU/Chassis/Power Fan Tachometer

CPU Quiet Fan

CPU Fan multi-speed control

CASE OPEN detection

Voltage monitoring: +12V, +5V, +3.3V, Vcore

OS Microso® Windows® 8.1 32-bit / 8.1 64-bit / 8 32-bit / 8 64-

bit / 7 32-bit / 7 64-bit / XP 32-bit / XP 64-bit

Certica-

tions

FCC, CE, WHQL

ErP/EuP ready (ErP/EuP ready power supply is required)

* For detailed product information, please visit our website:

http://www.asrock.com

AM1B-ITX

English

Please realize that there is a certain risk involved with overclocking, including adjust-

ing the setting in the BIOS, applying Untied Overclocking Technology, or using third-

party overclocking tools. Overclocking may aect your system’s stability, or even cause

damage to the components and devices of your system. It should be done at your own

risk and expense. We are not responsible for possible damage caused by overclocking.

Due to the operating system limitation, the actual memory size may be less than 4GB for

the reservation for system usage under Windows® 8 / 7 / XP. For Windows® 64-bit OS with

64-bit CPU, there is no such limitation. You can use ASRock XFast RAM to utilize the

memory that Windows® cannot use.

English

1.3 Unique Features

ASRock A-Tuning

A-Tuning is ASRock’s multi purpose soware suite with a new interface, more new

features and improved utilities, including XFast RAM, Dehumidier, Good Night

LED, FAN-Tastic Tuning and a whole lot more.

ASRock Instant Boot

ASRock Instant Boot allows you to turn on your PC in just a few seconds, provides a

much more ecient way to save energy, time, money, and improves system running

speed for your system. It leverages the S3 and S4 ACPI features which normally

enable the Sleep/Standby and Hibernation modes in Windows® to shorten boot

up time. By calling S3 and S4 at specic timing during the shutdown and startup

process, Instant Boot allows you to enter your Windows® desktop in a few seconds.

ASRock Instant Flash

ASRock Instant Flash is a BIOS ash utility embedded in Flash ROM. is conve-

nient BIOS update tool allows you to update the system BIOS in a few clicks without

preparing an additional oppy diskette or other complicated ash utility. Just save

the new BIOS le to your USB storage and launch this tool by pressing <F6> or

<F2> during POST to enter the BIOS setup menu to access ASRock Instant Flash.

Please be noted that the USB ash drive or hard drive must use FAT32/16/12 le

system.

ASRock APP Charger

Simply by installing the ASRock APP Charger makes your iPhone/iPad/iPod Touch

charge up to 40% faster than before on your computer. ASRock APP Charger allows

you to quickly charge many Apple devices simultaneously and even supports

continuous charging when your PC enters into Suspend to RAM (S3), hibernation

mode (S4) or power o (S5).

ASRock XFast LAN

ASRock XFast LAN provides faster internet access, which includes the benets

listed below. LAN Application Prioritization: You can congure your application’s

priority ideally and add new programs to the list. Lower Latency in Game: Aer

setting online game’s priority higher, it can lower the latency in games. Trac

Shaping: You can watch Youtube HD videos and download simultaneously. Real-

Time Analysis of Your Data: With the status window, you can easily recognize

which data streams you are currently transferring.

English

ASRock Easy Driver Installer

For users that don’t have an optical disk drive to install the drivers from our support

CD, Easy Driver Installer is a handy tool in the UEFI that installs the LAN driver

to your system via an USB storage device, then downloads and installs the other

required drivers automatically.

ASRock Interactive UEFI

ASRock Interactive UEFI is a blend of system conguration tools, cool sound eects

and stunning visuals. e unprecedented UEFI provides a more attractive interface

and more amusment.

ASRock Fast Boot

With ASRock ’s exclusive Fast Boot technology, it takes less than 1.5 seconds to

logon to Windows 8 from a cold boot. No more waiting! e speedy boot will

completely change your user experience and behavior.

ASRock Restart to UEFI

Windows® 8 brings the ultimate boot up experience. e lightning boot up speed

makes it hard to access the UEFI setup. ASRock Restart to UEFI allows users to

enter the UEFI automatically when turning on the PC. By enabling this function,

the PC will enter the UEFI directly aer you restart.

ASRock USB Key

In a world where time is money, why waste precious time everyday typing

usernames to log in to Windows? Why should we even bother memorizing those

foot long passwords? Just plug in the USB Key and let your computer log in to

windows automatically!

ASRock FAN-Tastic Tuning

ASRock FAN-Tastic Tuning is included in A-Tuning. Congure up to ve dierent

fan speeds using the graph. e fans will automatically shi to the next speed level

when the assigned temperature is met.

ASRock Good Night LED

ASRock Good Night LED technology oers you a better sleeping environment by

extinguishing the unessential LEDs. By enabling Good Night LED in the BIOS, the

Power/LAN LEDs will be switched o when the system is powered on. Good Night

LED will automatically switch o the Power and LAN LEDs when the system enters

into Standby/Hibernation mode as well.

AM1B-ITX

English

1.4 Motherboard Layout

AM1B-ITX

RoHS

CMOS

BATTERY

32Mb

BIO S

ATXPWR1

DDR3_A1 (64 bit, 240-pin module)

DDR3_A2 (64 bit, 240-pin module)

SATA3 _1

Super

I/O

LAN

AUDIO

CO DEC

CLR CMO S1

PCIE1

USB6_ 7

USB4_ 5

HD_AUD IO1

CP U_FA N1

CH A_FA N1

SPEAKE R1

HDL ED RES ET

PLE D PWR BTN

PANE L 1

Top :

LINE IN

Ce nt er :

FRONT

Bo tt om :

MI C IN

RJ-45 LAN

USB 3.0

T: USB0

B: USB1

CI1

SOCKET FS1b

SATA3 _2

Front USB 3.0

PWR_ FAN1

TPM S1

CO M1

USB 2.0

T: U SB0

B: USB1

PS2

Key boa rd/

Mouse

USB3 _2_ 3

SATA3 _A 1

SATA3 _A 2

PARALLEL PORT

VGA1 DVI1

HDMI1

English

No. Description

1 Power Fan Connector (PWR_FAN1)

2 Clear CMOS Jumper (CLRCMOS1)

3 CPU Fan Connector (CPU_FAN1)

4 Chassis Intrusion Header (CI1)

5 2 x 240-pin DDR3 DIMM Slots (DDR3_A1, DDR3_A2)

6 ATX Power Connector (ATXPWR1)

7 Chassis Speaker Header (SPEAKER1)

8 System Panel Header (PANEL1)

9 SATA3 Connector (SATA3_1)

10 SATA3 Connector (SATA3_2)

11 SATA3 Connector (SATA3_A2)

12 SATA3 Connector (SATA3_A1)

13 Chassis Fan Connector (CHA_FAN1)

14 USB 3.0 Header (USB3_2_3)

15 TPM Header (TPMS1)

16 COM Port Header (COM1)

17 USB 2.0 Header (USB4_5)

18 USB 2.0 Header (USB6_7)

19 Front Panel Audio Header (HD_AUDIO1)

AM1B-ITX

English

1.5 I/O Panel

No. Description No. Description

1 USB 2.0 Ports (USB01) 7 USB 3.0 Ports (USB3_0_1)

2 Parallel Port 8 HDMI Port

3 LAN RJ-45 Port* 9 DVI-D Port

4 Line In (Light Blue) 10 D-Sub Port

5 Front Speaker (Lime) 11 PS/2 Mouse/Keyboard Port

6 Microphone (Pink)

* ere are two LEDs on each LAN port. Please refer to the table below for the LAN port LED indications.

Activity / Link LED Speed LED

Status Description Status Description

O No Link O 10Mbps connection

Blinking Data Activity Orange 100Mbps connection

On Link Green 1Gbps connection

ACT/LINK LED

SPEED LED

LAN Port

1 3 5

679

English

is is a Mini-ITX form factor motherboard. Before you install the motherboard,

study the conguration of your chassis to ensure that the motherboard ts into it.

Pre-installation Precautions

Take note of the following precautions before you install motherboard components

or change any motherboard settings.

Make sure to unplug the power cord before installing or removing the motherboard.

Failure to do so may cause physical injuries to you and damages to motherboard

components.

In order to avoid damage from static electricity to the motherboard’s components,

NEVER place your motherboard directly on a carpet. Also remember to use a grounded

wrist strap or touch a safety grounded object before you handle the components.

Hold components by the edges and do not touch the ICs.

Whenever you uninstall any components, place them on a grounded anti-static pad or

in the bag that comes with the components.

When placing screws to secure the motherboard to the chassis, please do not over-

tighten the screws! Doing so may damage the motherboard.

Chapter 2 Installation

AM1B-ITX

English

2.1 Installing the CPU

Unplug all power cables before installing the CPU.

English

AM1B-ITX

English

2.2 Installing the CPU Fan and Heatsink

Aer you install the CPU into this motherboard, it is necessary to install a larger

heatsink and cooling fan to dissipate heat. You also need to spray thermal grease

between the CPU and the heatsink to improve heat dissipation. Make sure that the

CPU and the heatsink are securely fastened and in good contact with each other.

en connect the CPU fan to the CPU FAN connector. For proper installation,

please kindly refer to the instruction manuals of the CPU fan and the heatsink.

Please turn o the power or remove the power cord before changing a CPU or heatsink.

English

2.3 Installing Memory Modules (DIMM)

is motherboard provides two 240-pin DDR3 (Double Data Rate 3) DIMM slots.

e DIMM only ts in one correct orientation. It will cause permanent damage to

the motherboard and the DIMM if you force the DIMM into the slot at incorrect

orientation.

It is not allowed to install a DDR or DDR2 memory module into a DDR3 slot; other-

wise, this motherboard and DIMM may be damaged.

AM1B-IT X

English

AM1B-IT X

English

2.5 Jumpers Setup

e illustration shows how jumpers are setup. When the jumper cap is placed on

the pins, the jumper is “Short”. If no jumper cap is placed on the pins, the jumper

is “Open”. e illustration shows a 3-pin jumper whose pin1 and pin2 are “Short”

when a jumper cap is placed on these 2 pins.

Clear CMOS Jumper

(CLRCMOS1)

(see p.9, No. 2)

CLRCMOS1 allows you to clear the data in CMOS. To clear and reset the system

parameters to default setup, please turn o the computer and unplug the power

cord from the power supply. Aer waiting for 15 seconds, use a jumper cap to

short pin2 and pin3 on CLRCMOS1 for 5 seconds. However, please do not clear

the CMOS right aer you update the BIOS. If you need to clear the CMOS when

you just nish updating the BIOS, you must boot up the system rst, and then shut

it down before you do the clear-CMOS action. Please be noted that the password,

date, time, and user default prole will be cleared only if the CMOS battery is

removed.

Clear CMOSDefault

If you clear the CMOS, the case open may be detected. Please adjust the BIOS option

“Clear Status” to clear the record of previous chassis intrusion status.

English

2.6 Onboard Headers and Connectors

System Panel Header

(9-pin PANEL1)

(see p.9, No. 8)

Connect the power

switch, reset switch and

system status indicator on

the chassis to this header

according to the pin

assignments below. Note

the positive and negative

pins before connecting

the cables.

PWRBTN (Power Switch):

Connect to the power switch on the chassis front panel. You may congure the way to

turn o your system using the power switch.

RESET (Reset Switch):

Connect to the reset switch on the chassis front panel. Press the reset switch to restart

the computer if the computer freezes and fails to perform a normal restart.

PLED (System Power LED):

Connect to the power status indicator on the chassis front panel. e LED is on when

the system is operating. e LED keeps blinking when the system is in S3 sleep state.

e LED is o when the system is in S4 sleep state or powered o (S5).

HDLED (Hard Drive Activity LED):

Connect to the hard drive activity LED on the chassis front panel. e LED is on when

the hard drive is reading or writing data.

e front panel design may dier by chassis. A front panel module mainly consists

of power switch, reset switch, power LED, hard drive activity LED, speaker and etc.

When connecting your chassis front panel module to this header, make sure the wire

assignments and the pin assignments are matched correctly.

Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over

these headers and connectors. Placing jumper caps over the headers and connectors

will cause permanent damage to the motherboard.

AM1B-IT X

English

Serial ATA3 Connectors

(SATA3_1:

see p.9, No. 9)

(SATA3_2:

see p.9, No. 10)

(SATA3_A1:

see p.9, No. 12)

(SATA3_A2:

see p.9, No. 11)

ese four SATA3

connectors support SATA

data cables for internal

storage devices with up to

6.0 Gb/s data transfer rate.

USB 2.0 Headers

(9-pin USB4_5)

(see p.9, No. 17)

(9-pin USB6_7)

(see p.9, No. 18)

Besides two USB 2.0 ports

on the I/O panel, there

are two headers on this

motherboard. Each USB

2.0 header can support

two ports.

USB 3.0 Header

(19-pin USB3_2_3)

(see p.9, No. 14)

Besides two USB 3.0 ports

on the I/O panel, there

is one header on this

motherboard. is USB

3.0 header can support

two ports.

Front Panel Audio Header

(9-pin HD_AUDIO1)

(see p.9, No. 19)

is header is for

connecting audio devices

to the front audio panel.

SATA3_A1 SATA3_1

SATA3_A2 SATA3_2

In tA _P _D+

In tA _P _D-

GN D

In tA _P _SS TX +

In tA _P _SS TX -

GN D

In tA _P _SS RX +

Vb us

In tA _P _D+

In tA _P _D-

GN D

In tA _P _SS TX +

In tA _P _SS TX -

GN D

In tA _P _SS RX +

In tA _P _SS RX -

Vb us

In tA _P _S SRX -

English

Chassis Speaker Header

(4-pin SPEAKER1)

(see p.9, No. 7)

Please connect the chassis

speaker to this header.

Chassis and Power Fan

Connectors

(4-pin CHA_FAN1)

(see p.9, No. 13)

(3-pin PWR_FAN1)

(see p.9, No. 1)

Please connect fan cables

to the fan connectors and

match the black wire to

the ground pin.

CPU Fan Connector

(4-pin CPU_FAN1)

(see p.9, No. 3)

is motherboard pro-

vides a 4-Pin CPU fan

(Quiet Fan) connector.

If you plan to connect a

3-Pin CPU fan, please

connect it to Pin 1-3.

ATX Power Connector

(24-pin ATXPWR1)

(see p.9, No. 6)

is motherboard pro-

vides a 24-pin ATX power

connector. To use a 20-pin

ATX power supply, please

plug it along Pin 1 and Pin

13.

1. High Denition Audio supports Jack Sensing, but the panel wire on the chassis must

support HDA to function correctly. Please follow the instructions in our manual and

chassis manual to install your system.

2. If you use an AC’97 audio panel, please install it to the front panel audio header by

the steps below:

A. Connect Mic_IN (MIC) to MIC2_L.

B. Connect Audio_R (RIN) to OUT2_R and Audio_L (LIN) to OUT2_L.

C. Connect Ground (GND) to Ground (GND).

D. MIC_RET and OUT_RET are for the HD audio panel only. You don’t need to

connect them for the AC’97 audio panel.

E. To activate the front mic, go to the “FrontMic” Tab in the Realtek Control panel

and adjust “Recording Volume”.

GND

+12V

CPU_FAN _S P EED

FA N_ SPEED_CO N TR OL

AM1B-IT X

English

Serial Port Header

(9-pin COM1)

(see p.9, No. 16)

is COM1 header

supports a serial port

module.

Chassis Intrusion Header

(2-pin CI1)

(see p.9, No. 4)

is motherboard

supports CASE OPEN

detection feature that

detects if the chassis cove

has been removed. is

feature requires a chassis

with chassis intrusion

detection design.

TPM Header

(17-pin TPMS1)

(see p.9, No. 15)

is connector supports

Trusted Platform Module

(TPM) system, which can

securely store keys, digital

certicates, passwords,

and data. A TPM system

also helps enhance

network security, protects

digital identities, and

ensures platform integrity.

G ND

S MB_D AT A_MAI N

LAD2

LAD1

G ND

S _PWR DW N#

S ERIR Q#

G ND

P CICL K

P CIRS T#

LAD3

+ 3V

LAD0

+ 3VSB

G ND

F RAME S MB_C LK _M AIN

English

Chapter 3 Software and Utilities Operation

3.1 Installing Drivers

e Support CD that comes with the motherboard contains necessary drivers and

useful utilities that enhance the motherboard’s features.

Running The Support CD

To begin using the support CD, insert the CD into your CD-ROM drive. e CD

automatically displays the Main Menu if “AUTORUN” is enabled in your computer.

If the Main Menu does not appear automatically, locate and double click on the le

“ASRSETUP.EXE” in the Support CD to display the menu.

Drivers Menu

e drivers compatible to your system will be auto-detected and listed on the

support CD driver page. Please click or follow the order from top to Install All

bottom to install those required drivers. erefore, the drivers you install can work

properly.

Utilities Menu

e Utilities Menu shows the application soware that the motherboard supports.

Click on a specic item then follow the installation wizard to install it.

To improve Windows 7 compatibility, please download and install the following hot

x provided by Microso.

“KB2720599”: http://support.microso.com/kb/2720599/en-us

AM1B-IT X

English

3.2 A-Tuning

A-Tuning is ASRock’s multi purpose soware suite with a new interface, more new

features and improved utilities, including XFast RAM, Dehumidier, Good Night

LED, FAN-Tastic Tuning and a whole lot more.

3.2.1 Installing A-Tuning

When you install the all-in-one driver to your system from ASRock’s support CD,

A-Tuning will be auto-installed as well. Aer the installation, you will nd the icon

“A-Tuning“ on your desktop. Double-click the “A-Tuning“ icon, A-Tuning

main menu will pop up.

3.2.2 Using A-Tuning

ere are ve sections in A-Tuning main menu: Operation Mode, Tools, OC

Tweaker, System Info and Tech Service.

Operation Mode

Choose an operation mode for your computer.

English

Tools

Various tools and utilities.

XFast RAM

Boost the system’s performance and extend the HDD’s or SDD’s lifespan! Create a

hidden partition, then assign which les should be stored in the RAM drive.

Fast Boot

Fast Boot minimizes your computer's boot time. Please note that Ultra Fast mode

is only supported by Windows 8 and the VBIOS must support UEFI GOP if you are

using an external graphics card.

OMG

Schedule the starting and ending hours of Internet access granted to other users.

Place X marks on the time table to disable the Internet.

Good Night LED

Switch o the Power/LAN LEDs when the system is on, and automatically switch o

the Power and LAN LEDs when the system enters into Standby/Hibernation mode.

FAN-Tastic Tuning

Congure up to ve dierent fan speeds using the graph. e fans will automatically

shi to the next speed level when the assigned temperature is met.

AM1B-IT X

English

Dehumidier

Prevent motherboard damages due to dampness. Enable this function and

congure the period of time until the computer powers on, and the duration of the

dehumidifying process.

System Info

View information about the system.

Tech Service

Contact Tech Service.

English

3.3 Start8

For those Windows 8 users who miss the Start Menu, Start8 is an ideal solution that

brings back the familiar Start Menu along with added customizations for greater

eciency.

3.3.1 Installing Start8

Install , which is located in the folder at the following path of the Support CD: Start8

\ .ASRock Utility > Start8

3.3.2 Conguring Start8

Style

Select between the Windows 7 style and Windows 8 style Start Menu. en select

the theme of the Start Menu and customize the style of the Start icon.

English

Control lets you congure what a click on the start button or a press on the

Windows key does.

Desktop

Desktop allows you to disable the hot corners when you are working on the desktop.

It also lets you choose whether or not the system boots directly into desktop mode

and bypass the Metro user interface.

About

Displays information about Start8.

AM1B-IT X

English

Chapter 4 UEFI SETUP UTILITY

4.1 Introduction

ASRock Interactive UEFI is a blend of system conguration tools, cool sound eects

and stunning visuals. Not only will it make BIOS setup less dicult but also a lot

more amusing. is section explains how to use the UEFI SETUP UTILITY to

congure your system. You may run the UEFI SETUP UTILITY by pressing <F2>

or <Del> right aer you power on the computer, otherwise, the Power-On-Self-Test

(POST) will continue with its test routines. If you wish to enter the UEFI SETUP

UTILITY aer POST, restart the system by pressing <Ctl> + <Alt> + <Delete>, or

by pressing the reset button on the system chassis. You may also restart by turning

the system o and then back on.

4.1.1 UEFI Menu Bar

e top of the screen has a menu bar with the following selections:

Main For setting system time/date information

OC Tweaker For overclocking congurations

Advanced For advanced system congurations

Tool Useful tools

H/W Monitor Displays current hardware status

Boot For conguring boot settings and boot priority

Security For security settings

Exit Exit the current screen or the UEFI Setup Utility

Because the UEFI soware is constantly being updated, the following UEFI setup

screens and descriptions are for reference purpose only, and they may not exactly

match what you see on your screen.

English

4.1.2 Navigation Keys

Use < > key or < > key to choose among the selections on the menu bar, and

use < > key or < > key to move the cursor up or down to select items, then

press <Enter> to get into the sub screen. You can also use the mouse to click your

required item.

Please check the following table for the descriptions of each navigation key.

Navigation Key(s) Description

+ / - To change option for the selected items

<Tab> Switch to next function

<PGUP> Go to the previous page

<PGDN> Go to the next page

<HOME> Go to the top of the screen

<END> Go to the bottom of the screen

<F1> To display the General Help Screen

<F7> Discard changes and exit the SETUP UTILITY

<F9> Load optimal default values for all the settings

<F10> Save changes and exit the SETUP UTILITY

<F12> Print screen

<ESC> Jump to the Exit Screen or exit the current screen

AM1B-IT X

English

4.2 Main Screen

When you enter the UEFI SETUP UTILITY, the Main screen will appear and

display the system overview.

Active Page on Entry

Select the default page when entering the UEFI setup utility.

English

Because the UEFI soware is constantly being updated, the following UEFI setup

screens and descriptions are for reference purpose only, and they may not exactly

match what you see on your screen.

4.3 OC Tweaker Screen

In the OC Tweaker screen, you can set up overclocking features.

DRAM Timing Conguration

DRAM Frequency

If [Auto] is selected, the motherboard will detect the memory module(s) inserted

and assign the appropriate frequency automatically.

English

Command Rate (CR)

e delay between when a memory chip is selected and when the rst active command can

be issued.

RAS# Cycle Time (tRC)

Use this item to change RAS# Cycle Time (tRC) Auto/Manual setting.

Write Recovery Time (tWR)

e amount of delay that must elapse aer the completion of a valid write operation,

before an active bank can be precharged.

Refresh Cycle Time (tRFC)

e number of clocks from a Refresh command until the rst Activate command to

the same rank.

RAS to RAS Delay (tRRD)

e number of clocks between two rows activated in dierent banks of the same

rank.

Write to Read Delay (tWTR)

e number of clocks between the last valid write operation and the next read

command to the same internal bank.

Read to Precharge (tRTP)

e number of clocks that are inserted between a read command to a row pre-

charge command to the same rank.

Four Activate Window (tFAW)

e time window in which four activates are allowed the same rank.

Voltage Conguration

DRAM Voltage

Use this to select DRAM Voltage. e default value is [Auto].

English

4.4.1 CPU Conguration

Cool 'n' Quiet

Use this item to enable or disable AMD’s Cool ‘n’ Quiet

TM technology. e default

value is [Enabled]. Conguration options: [Enabled] and [Disabled]. If you install

Windows®

8 / 7 / XP and want to enable this function, please set this item to [Enabled].

Please note that enabling this function may reduce CPU voltage and memory

frequency, and lead to system stability or compatibility issue with some memory

modules or power supplies. Please set this item to [Disable] if above issue occurs.

SVM

When this option is set to [Enabled], a VMM (Virtual Machine Architecture) can

utilize the additional hardware capabilities provided by AMD-V. e default value is

[Enabled]. Conguration options: [Enabled] and [Disabled].

Core C6 Mode

Use this item to enable or disable Core C6 mode. e default value is [Enabled].

AM1B-IT X

English

4.4.2 Chipset Conguration

Share Memory

Congure the size of memory that is allocated to the integrated graphics processor

when the system boots up.

Primary Graphics Adapter

Select a primary VGA.

Onboard HDMI HD Audio

Enable audio for the onboard digital outputs.

Onboard HD Audio

Enable/disable onboard HD audio. Set to Auto to enable onboard HD audio and

automatically disable it when a sound card is installed.

Front Panel

Enable/disable front panel HD audio.

Onboard LAN

Enable or disable the onboard network interface controller.

AM1B-ITX

English

4.4.3 Storage Conguration

SATA Controller(s)

Enable/disable the SATA controllers.

SATA Mode Selection

IDE: For better compatibility.

AHCI: Supports new features that improve performance.

Hard Disk S.M.A.R.T.

S.M.A.R.T stands for Self-Monitoring, Analysis, and Reporting Technology. It is a

monitoring system for computer hard disk drives to detect and report on various

indicators of reliability.

ASMedia SATA3 Mode

IDE: For better compatibility.

AHCI: Supports new features that improve performance.

AHCI (Advanced Host Controller Interface) supports NCQ and other new

features

that will improve SATA disk performance but IDE mode does not have these advan-

tages.

English

4.4.4 Super IO Conguration

Serial Port

Enable or disable the Serial port.

Serial Port Address

Select the address of the Serial port.

Parallel Port

Enable or disable the Parallel port.

Change Settings

Select the address of the Parallel port.

Device Mode

Select the device mode according to your connected device.

AM1B-ITX

English

4.4.5 ACPI Conguration

Suspend to RAM

It is recommended to select auto for ACPI S3 power saving.

Check Ready Bit

Enable to enter the operating system aer S3 only when the hard disk is ready, this

is recommended for better system stability.

Deep Sleep

Congure deep sleep mode for power saving when the computer is shut down.

ACPI HPET Table

Enable the High Precision Event Timer for better performance and to pass WHQL

tests.

PS/2 Keyboard Power On

Allow the system to be waked up by a PS/2 Keyboard.

PCI Devices Power On

Allow the system to be waked up by a PCI device and enable wake on LAN.

English

Ring-In Power On

Allow the system to be waked up by onboard COM port modem Ring-In signals.

RTC Alarm Power On

Allow the system to be waked up by the real time clock alarm. Set it to By OS to let

it be handled by your operating system.

USB Keyboard/Remote Power On

Allow the system to be waked up by an USB keyboard or remote controller.

USB Mouse Power On

Allow the system to be waked up by an USB mouse.

AM1B-ITX

English

4.4.6 USB Conguration

USB Controller

Enable or disable all the USB ports.

USB 3.0 Controller

Enable or disable all the USB 3.0 ports.

Legacy USB Support

Enable or disable Legacy OS Support for USB 2.0 devices. If you encounter USB

compatibility issues it is recommended to disable legacy USB support. Select UEFI

Setup Only to support USB devices under the UEFI setup and Windows/Linux

operating systems only.

Legacy USB 3.0 Support

Enable or disable Legacy OS Support for USB 3.0 devices.

English

4.4.7 Trusted Computing

Security Device Support

Enable to activate Trusted Platform Module (TPM) security for your hard disk

drives.

AM1B-ITX

English

4.5 Tools

OMG (Online Management Guard)

Administrators are able to establish an internet curfew or restrict internet access

at specied times via OMG. You may schedule the starting and ending hours of

internet access granted to other users. In order to prevent users from bypassing

OMG, guest accounts without permission to modify the system time are required.

UEFI Tech Service

Contact ASRock Tech Service if you are having trouble with your PC. Please setup

network conguration before using UEFI Tech Service.

Easy Driver Installer

For users that don’t have an optical disk drive to install the drivers from our support

CD, Easy Driver Installer is a handy tool in the UEFI that installs the LAN driver

to your system via an USB storage device, then downloads and installs the other

required drivers automatically.

Instant Flash

Save UEFI les in your USB storage device and run Instant Flash to update your

UEFI.

Product specificaties

Merk:	Asrock
Categorie:	Moederbord
Model:	AM1B-ITX
Breedte:	- mm
Diepte:	- mm
Ethernet LAN:	Ja
Maximum resolutie:	2048 x 1536 Pixels
Type stroombron:	ATX
Meegeleverde kabels:	SATA
Aantal USB 2.0-poorten:	2
VGA (D-Sub)poort(en):	1
Aantal HDMI-poorten:	1
Microfoon, line-in ingang:	Ja
Aantal Ethernet LAN (RJ-45)-poorten:	1
Hoofdtelefoonuitgangen:	1
HDCP:	Ja
DVI-D poorten:	1
Aantal poorten USB 3.2 Gen 1 (3.1 Gen 1) Type A:	2
Processor socket:	Socket AM1
Processorfabrikant:	AMD
Maximum intern geheugen:	32 GB
Audio-uitgangskanalen:	5.1 kanalen
Snelle installatiehandleiding:	Ja
Ethernet interface type:	Fast Ethernet, Gigabit Ethernet
Geheugen slots type:	DIMM
Audiochip:	Realtek ALC662
Meegeleverde drivers:	Ja
Grafische adapter-familie:	AMD
Type koeling:	Passief
Geheugen kanaal:	Dubbelkanaals
Ondersteunde opslagstationinterfaces:	SATA III
PS/2 poort(en):	1
Component voor:	PC
LAN controller:	Realtek RTL8111GR
DirectX versie:	11.1
Aantal SATA III connectors:	4
Non-ECC:	Ja
Wake-on-LAN:	Ja
Compatibele processors:	AMD Athlon, AMD Sempron
Parallelle poort(en):	1
Ondersteunde geheugen types:	DDR3-SDRAM
Max. aantal SMP-processoren:	1
Moederbord chipset familie:	AMD
Moederbord form factor:	mini ITX
Aantal geheugenslots:	2
Supported memory clock speeds:	1066,1333,1600 MHz
BIOS type:	UEFI AMI
Grootte BIOS-geheugen:	32 Mbit
ACPI version:	1.1
COM aansluitingen:	1
Aansluiting voor CPU koeler:	Ja
Aansluitingen voor behuizingsventilatoren:	1
ATX Power connector (24-pin):	Ja
Aansluiting voor ventilator van voeding:	Ja
USB 2.0 aansluitingen:	2
Aansluiting voor audiopaneel aan voorzijde:	Ja
PC gezondheids monitor:	CPU, FAN
Niet gebufferd geheugen:	Ja
USB 3.2 Gen 1 (3.1 Gen 1)-aansluitingen:	1
TPM connector:	Ja
Chassis intrusion aansluiting:	Ja
Discrete grafische ondersteuning:	Ja
PCI Express x16 (Gen 2.x) slots:	1