Ariston Thermo A1637 Handleiding

Ariston Thermo Wasmachine A1637

Lees hieronder de 📖 handleiding in het Nederlandse voor Ariston Thermo A1637 (12 pagina's) in de categorie Wasmachine. Deze handleiding was nuttig voor 52 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/12

Contents

WASHING MACHINE

Instruction booklet

Installation, 2-3

Unpacking

Remove the transit fixings

Levelling

Water connections

Drainage and electrical connections

Technical details

Washing machine description, 4-5

Control panel

LEDs

Starting and programmes, 6

Briefly: how to start a programme

Programmes table

Personalisation, 7

Setting the temperature

Setting the spin speeds

Functions

Detergents and laundry, 8

Detergent dispenser

Preparing your laundry

Special items

Precautions and Advice, 9

General safety

Disposal

Saving energy and respecting the environment

Care and Maintenance, 10

Switching off the water or electricity supply

Cleaning your appliance

Cleaning the pump

Caring for your appliance door and drum

Checking the water inlet hose

Fuses

Changing the plug

Troubleshooting, 11

Service, 12

Before calling for assistance

Spare parts

English

A1637

A1437

A1237

!Packaging materials are not childrens toys.

Levelling

1. Install the machine on a flat sturdy floor, without

resting it up against walls, cabinets etc.

2. Compensate for any unevenness by tightening or

loosening the adjustable front feet. When adjusting

the feet, use a spirit level to check the machine

stands level, from side to side and from front to

back.

Levelling your appliance correctly will provide it with

stability and avoid any vibrations, noise and shifting

during operation. If it is placed on a fitted or loose

carpet, adjust the feet in such a way as to allow

enough room for ventilation beneath the washing

machine.

Water connection

Connecting the water inlet hose.

Remember that this is a cold-fill machine and the fill

hose fitted to the rear of the machine must be

connected to the cold water supply.

Before making the connections to the water outlet,

allow the water to run freely from the cold water

supply tap until it is perfectly clear.

Screw the cold water fill hose

onto the cold water supply tap

until tight.

Turn the tap on and check for leaks:

tighten if necessary.

!Make sure there are no kinks or bends in the hose.

!The water pressure at the tap must be within the values

indicated in the Technical details table (next page).

!If the water inlet hose is not long enough, contact a

specialist store or an authorised serviceman.

!Always use new hoses.

!Check the water hose at least once a year, replace

any that are cracked as worn hoses could split under

water pressure.

Installation

!Keep this instruction manual in a safe place for

future reference. Should the appliance be sold,

transferred or moved, make sure the instruction manual

accompanies the washing machine to inform the new

owner as to its operation and features.

!Read these instructions carefully: they contain vital

information on installation, use and safety.

Unpacking

1. Unpack the machine.

2. Check whether the washing machine has been

damaged during transport. If this is the case, do

not install it and contact your retailer.

Remove the transit fixings

IMPORTANT: Follow these instructions to remove the

TWO transit fixings.

Situated one either side of the

rear panel, BOTH transit bolts

MUST be removed before use.

!Failure to do so may cause

damage to your machine.

It is important the transit bolt and

spacer ( ) come out intact.see pic

1. Unscrew the bolt using a

13mm spanner.

2. STOP when 3 threads can be

seen.

3. Hold, slide sideways and pull

to remove.

4. For safety, insert one of the

plastic covers (supplied with

your machine) over the hole.

!Repeat steps 1 to 4 to remove

the second transit bolt.

The first wash cycle

Once the appliance has been installed and before you

use it for the first time, run a wash cycle without

detergent and no laundry, setting the 90˚C programme

without a pre-wash cycle.

Models A1637

A1437

A1237

59.5cm wide

Dimensions 85cm high

60cm deep

Capacity from 1 to 7kg Wash

Electric voltage 220/240 Volts 50Hz

connections maximum absorbed power:

1700W-2100W

Water maximum pressure 1 MPa (10 bar)

connections minimum pressure 0.05 MPa (0.5 bar)

drum capacity 54 litres

Spin Speed up to 1600 rpm - A1637

up to 1400 rpm - A1437

up to 1200 rpm - A1237

Control programme 3

programmes temperature 60˚C

according to - run with a 7kg load

IEC456

directive

This appliance is compliant with the

following European Community

Directives:

- 73/23/EEC & 93/68/EEC

(Low Voltage) and subsequent amendments.

- 89/336/EEC,92/31/EEC & 93/68/EEC

(Electromagnetic Compatibility) and subsequent

amendments.

Drainage connections

A. Connect the drain hose,

without kinking it, to a

draining duct or a wall

drain fixed at a height

between 65 and 100cm

from the floor.

B. Alternatively, place it

over the edge of a basin,

sink or tub, fastening the

hose supplied to the tap.

The free end of the hose

should not be under

water.

!We advise against the use of hose extensions. In

case of absolute need, the extension must have the

same diameter as the original hose and must not

exceed 150cm in length.

Electrical connections

Before plugging the appliance into the mains socket,

make sure that:

●The socket is earthed and in compliance with the

applicable law.

●The socket is able to sustain the appliances

maximum power load indicated in the Technical

Details table (on the right).

●The supply voltage is included within the values

indicated in the Technical Details table (on the right).

●The socket is compatible with the machines plug.

If this is not the case, replace the socket or the

plug.

!The machine should not be installed in an outdoor

environment, not even when the area is sheltered,

because it may be very dangerous to leave it exposed

to rain and thunderstorms.

!When the machine is installed, the mains socket

must be within easy reach and should be connected

to a suitable electrical supply.

!Do not use extensions or multiple sockets.

!The power supply cable must never be bent or

dangerously compressed.

!The power supply cable must only be replaced by

an authorised serviceman.

!The company denies all liability if and when these

norms are not respected.

Technical Details

Installation

Product specificaties

Merk:	Ariston Thermo
Categorie:	Wasmachine
Model:	A1637

Heb je hulp nodig?

Als je hulp nodig hebt met Ariston Thermo A1637 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Wasmachine Ariston Thermo

Ariston Thermo LI65EU Handleiding

5 Juni 2023

Ariston Thermo AVTF129 Handleiding

25 Mei 2023

Ariston Thermo RSF82BAUS Handleiding

24 Mei 2023

Ariston Thermo AQXL 125 Handleiding

24 Mei 2023

Ariston Thermo A1235 Handleiding

24 Mei 2023

Ariston Thermo LBE129 Handleiding

9 Mei 2023

Ariston Thermo BS1400 Handleiding

8 Mei 2023

Ariston Thermo LI 670 W NA Handleiding

4 Mei 2023

Ariston Thermo RPD1067DAUS Handleiding

29 April 2023

Ariston Thermo AVSL125 Handleiding

29 April 2023

Handleiding Wasmachine

Nieuwste handleidingen voor Wasmachine

Otsein LB LTO129A Handleiding

21 November 2024

Otsein LB LTO109A Handleiding

21 November 2024

Otsein-Hoover LB HV16ESALU Handleiding

21 November 2024

Sangiorgio ST6512EL Handleiding

21 November 2024

Sangiorgio FS614D9 Handleiding

21 November 2024

Sangiorgio PROGETTO F4 Handleiding

21 November 2024

Sangiorgio SG710 Handleiding

21 November 2024

Sangiorgio F814DIBC Handleiding

21 November 2024

Sangiorgio F812D Handleiding

21 November 2024

Sangiorgio F812L Handleiding

21 November 2024