Ariston Thermo A1600WD Handleiding

Ariston Thermo Wasmachine A1600WD

Lees hieronder de 📖 handleiding in het Nederlandse voor Ariston Thermo A1600WD (16 pagina's) in de categorie Wasmachine. Deze handleiding was nuttig voor 50 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/16

Contents

WASHER DRYER

A1600WD

A1400SWD

A1400WD

A1200WD

Instruction booklet

Installation, 2-3

Unpacking

Remove the transit fixings

Levelling

Water connections

Drainage and electrical connections

Technical details

Washer dryer description, 4-5

Control panel

LEDs

Starting and programmes, 6-9

Briefly: how to start a programme

Programmes table

Setting the temperature

Setting the spin speeds

Functions

Drying section

Detergents and laundry, 10

Detergent dispenser

Preparing your laundry

Special items

Precautions and Advice, 11

General safety

Disposal

Saving energy and respecting the environment

Care and Maintenance, 12

Switching off the water or electricity supply

Cleaning

Caring for your appliance door and drum

Checking the water inlet hoses

Fuses

Changing the plug

Troubleshooting, 13-14

Service, 15

Before calling for assistance

Spare parts

English

!Packaging materials are not childrens toys.

Levelling

1. Install the machine on a flat sturdy floor, without

resting it up against walls, cabinets etc.

2. Compensate for any unevenness by tightening or

loosening the adjustable front feet. When adjusting

the feet, use a spirit level to check the machine

stands level, from side to side and from front to

back.

Levelling your appliance correctly will provide it with

stability and avoid any vibrations, noise and shifting

during operation. If it is placed on a fitted or loose

carpet, adjust the feet in such a way as to allow

enough room for ventilation beneath the machine.

Water connection

Connecting the water inlet hose.

Remember that this is a cold-fill machine and the fill

hose fitted to the rear of the machine must be

connected to the cold water supply.

Before making the connections to the water outlet,

allow the water to run freely from the cold water

supply tap until it is perfectly clear.

Screw the cold water fill hose

onto the cold water supply tap

until tight.

Turn the tap on and check for leaks:

tighten if necessary.

!Make sure there are no kinks or bends in the hose.

!The water pressure at the tap must be within the values

indicated in the Technical details table (next page).

!If the water inlet hose is not long enough, contact a

specialist store or an authorised serviceman.

!Always use new hoses.

!Check the water hose at least once a year, replace

any that are cracked as worn hoses could split under

water pressure.

Installation

GB !Keep this instruction manual in a safe place for

future reference. Should the appliance be sold,

transferred or moved, make sure the instruction manual

accompanies the washer dryer to inform the new

owner as to its operation and features.

!Read these instructions carefully: they contain vital

information on installation, use and safety.

Unpacking

1. Unpack the machine.

2. Check whether the washer dryer has been

damaged during transport. If this is the case, do not

install it and contact your retailer.

Remove the transit fixings

IMPORTANT: Follow these instructions to remove the

TWO transit fixings.

Situated one either side of the

rear panel, BOTH transit bolts

MUST be removed before use.

!Failure to do so may cause

damage to your machine.

It is important the transit bolt and

spacer ( ) come out intact.see pic

1. Unscrew the bolt using a

13mm spanner.

2. STOP when 3 threads can be

seen.

3. Hold, slide sideways and pull

to remove.

4. For safety, insert one of the

plastic covers (supplied with

your machine) over the hole.

!Repeat steps 1 to 4 to remove

the second transit bolt.

The first wash cycle

Once the appliance has been installed and before you

use it for the first time, run a wash cycle without

detergent and no laundry, setting the 90˚C

programme without a pre-wash cycle.

Models A1600WD, A1400SWD,

A1400WD, A1200WD

59.5cm wide

Dimensions 85cm high

60cm deep

Capacity from 1 to 6kg

Electric voltage 220/240 Volts 50Hz

connections maximum absorbed power:

1700W-2100W

Water maximum pressure 1 MPa (10 bar)

connections minimum pressure 0.05 MPa (0.5 bar)

drum capacity 53 litres

Spin Speed up to 1600 rpm - A1600WD

up to 1400 rpm - A1400SWD,

A1400WD

up to 1200 rpm - A1200WD

Control programme 3

programmes temperature 60˚C

according to

IEC50229 - dry run with a 1kg load followed by

directive a 5kg load for model A1600WD

-dry run with a 2kg load followed by

a 4kg load for models A1400SWD,

A1400WD and A1200WD

This appliance is compliant with the

following European Community

Directives:

- 72/23/CEE of 19/02/73

(Low Voltage) and subsequent amendments.

- 89/336/CEE of 03/05/89 (Electromagnetic

Compatibility) and subsequent amendments.

Drainage connections

A. Connect the drain

hose, without kinking it,

to a draining duct or a

wall drain fixed at a

height between 65 and

100cm from the floor.

Use the curved bracket,

if reqired.

B. Alternatively, place

it over the edge of a

basin, sink or tub,

fastening the hose

supplied to the tap.

!The free end of the hose should not be under water.

!We advise against the use of hose extensions. In

case of absolute need, the extension must have the

same diameter as the original hose and must not

exceed 150cm in length.

Electrical connections

Before plugging the appliance into the mains socket,

make sure that:

●the socket is earthed and in compliance with the

applicable law.

●the socket is able to sustain the appliances

maximum power load indicated in the Technical

Details table (on the right).

●the supply voltage is included within the values

indicated in the Technical Details table (on the

right).

●the socket is compatible with the machines plug.

If this is not the case, replace the socket or the

plug.

!The machine should not be installed in an outdoor

environment, not even when the area is sheltered,

because it may be very dangerous to leave it exposed

to rain and thunderstorms.

!When the machine is installed, the mains socket

must be within easy reach and should be connected

to a suitable electrical supply.

!Do not use extensions or multiple sockets.

!The power supply cable must never be bent or dan-

gerously compressed.

!The power supply cable must only be replaced by

an authorised serviceman.

!The company denies all liability if and when these

norms are not respected.

Technical Details

Installation

Product specificaties

Merk:	Ariston Thermo
Categorie:	Wasmachine
Model:	A1600WD

Heb je hulp nodig?

Als je hulp nodig hebt met Ariston Thermo A1600WD stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Wasmachine Ariston Thermo

Ariston Thermo LI65EU Handleiding

5 Juni 2023

Ariston Thermo AVTF129 Handleiding

25 Mei 2023

Ariston Thermo RSF82BAUS Handleiding

24 Mei 2023

Ariston Thermo AQXL 125 Handleiding

24 Mei 2023

Ariston Thermo A1235 Handleiding

24 Mei 2023

Ariston Thermo LBE129 Handleiding

9 Mei 2023

Ariston Thermo BS1400 Handleiding

8 Mei 2023

Ariston Thermo LI 670 W NA Handleiding

4 Mei 2023

Ariston Thermo RPD1067DAUS Handleiding

29 April 2023

Ariston Thermo AVSL125 Handleiding

29 April 2023

Handleiding Wasmachine

Nieuwste handleidingen voor Wasmachine

Otsein LB LTO129A Handleiding

21 November 2024

Otsein LB LTO109A Handleiding

21 November 2024

Otsein-Hoover LB HV16ESALU Handleiding

21 November 2024

Sangiorgio ST6512EL Handleiding

21 November 2024

Sangiorgio FS614D9 Handleiding

21 November 2024

Sangiorgio PROGETTO F4 Handleiding

21 November 2024

Sangiorgio SG710 Handleiding

21 November 2024

Sangiorgio F814DIBC Handleiding

21 November 2024

Sangiorgio F812D Handleiding

21 November 2024

Sangiorgio F812L Handleiding

21 November 2024