Apc Line-R LSW1200-IND Handleiding

Apc Niet gecategoriseerd Line-R LSW1200-IND

Lees hieronder de 📖 handleiding in het Nederlandse voor Apc Line-R LSW1200-IND (1 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 16 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/1

Safety Messages



Safety Information

Adhere to all national and local electrical codes.

All wiring must be performed by a qualified electrician.

Changes and modifications to this unit not expressly approved by APC by Schneider Electric

could void the warranty.

This product is intended for indoor use only.

Do not operate this product in direct sunlight, in contact with fluids, or where there is excessive

dust or humidity.

Do not block the air vents on the AVR. Allow adequate space for proper ventilation. Allow



1 inch (2.5 cm) minimum vent clearance.

Product Description

The Line-R automatically corrects brownouts (by boosting low voltage) and overvoltages (by stepping

down high voltage) from the power utility service to levels that are acceptable for computers, as well as other

sensitive equipment. APC by Schneider Electric Line-R provides a high degree of protection from line

voltage sags and swells, and has been designed for reliable, maintenance-free service.

Applications

Features

Installation

Specifications

Limited Warranty

CAUTION

NOTICE



Line-R

Automatic Voltage Regulator

Models LSW500-IND, LSW800-IND,

LSW1200-IND, and LSW2000-IND

EN 990-91153

08/2018

CAUTION in dicates a hazardous s ituation which, if not avoided, could result in minor or

moderate injury.

NOTICE is used to address p ractices not related to physical injury.

Top Panel

Power LE D Illuminates when input vo ltage is

within normal range

AV R LE D

AC Out lets

Illuminates when input vo ltage is

below or higher the rated Input

Voltage Range

These outlets supply power to

connected equipment when the Lin e-R

is connected to AC power

Rear Panel

Power Sw itch

AC Powe r

Cord

Use this as the master power switch to

turn the Line-R and all connected

equipment on ( ) or off ( ).

Use this cable to connect the Line-R to

AC power.

Plug the Line-R into a Wall Outlet - Plug the Line-R into a wall socket. Connect your computer or

other electronic equipment to any of the three outlets on the top panel of the Line-R. The Line-R

should only be used in buildings that have proper grounding on a branch circuit protected by a fuse

or circuit breaker.

Connect Your Equipment - Plug equipment into the Line-R top-panel outlets and switch the

equipment ON. The equipment will not be powered until the Line-R is switched on.

Note: The total power consumption of all equipment plugged into the Line-R must not exceed the

ratings listed in the Specifications table below.

Switch ON the Line-R - Press the back panel power switch to the on ( ) position. This switch

may be used as the master switch for the device and all equipment connected to it.

Characteristics LSW800-INDLSW500-IND LSW1200-IND

Maximum Output Power Capacity

Nominal Output Voltage

Nominal Input Current

Acceptable Voltage Range Tolerance

400 W or 800 VA250 W or 500 VA 600 W or 1200 VA

230V

1.56 A 2.5 A 3.75 A

Rated Input Voltage

Maximum Acceptable Input Voltage

Output Regulation

Response Time

Efficiency

Nominal Frequency

Number of Outlets

Operating Temperature

Relative Humidity

Weight

Dimensions

1.6 kg (3.5 lb) 1.96 kg (4.3 lb)

160-284 VAC

230 Vac

284 Vac

>95%

50 Hz

32 - 104 F (0 - 40 C )

0-90% Non-condensing

7 0 x 3.7 x 4.5 inches (180 x 95 x 119 mm).

6 ms

Surge Energy 148 Joules

Electric Industries S A S . . . or their affiliated companies All . other trademarks are property of

their respective owners .

Note: The total power consumption of all equipment plugged into the Line-R must not exceed the

“Maximum Output Power Capacity” rating listed in the Specifications table.

The Line-R is designed for use with voltage sensitive equipment such as computers, monitors,

printers, scanners, televisions, stereos or other AV equipment.

Do not use with life sustaining equipment and any device with a power requirement exceeding the

“Acceptable Voltage Range” rating listed in the Specifications table.

Read the instructions carefully to become familiar with the equipment before attempting to install,

operate, service or maintain the AVR (Automatic Voltage Regulator). The following special messages

may appear throughout this manual or on the equipment to warn of potential hazards or to call

attention to information that clarifies or simplifies a procedure.

The addition of this symbol to a “Danger” or “Warning” safety label indicates that an

electrical hazard exists which will result in personal injury if the instructions are not

followed.

This is the safety alert symbol. It is used to alert you to potential personal injury

hazards. Obey all safety messages that follow this symbol to avoid possible

injury or death.

APC by Schneider Electric IT Customer Support Worldwide

For country specific customer support, go to the APC by Schneider Electric Web site, www.apc.com.

Schneider Electric IT (SEIT) warrants its products to be free from defects in materials and

workmanship for a period of two years from the date of purchase. SE IT obligation under this

warranty is limited to repairing or replacing, at its sole discretion, any such defective

products. This warranty does not apply to battery wear from use, equipment that has been

damaged by accident, negligence or misapplication or has been altered or modified in any

way. SEIT standard procedure is to replace the original unit with a factory reconditioned

unit. Customers who must have the original unit back due to the assignment of asset tags and

set depreciation schedules must declare such a need at first contact with an SEIT Technical

Support representative. SEIT will ship the replacement unit once the defective unit has been

received by the repair department, or cross ship upon the receipt of a valid credit card

number. The customer pays for shipping the unit to SEIT. SEIT pays ground freight

transportation costs to ship the replacement unit to the customer. For full warranty

information refer to www.apc.com.

8.2 x 4.3 x 5.1 inches (210 x 110 x 132 mm)

LSW2000-IND

1000 W or 2000 VA

6.25 A

3.05 kg (6.7 lb) 3.72 kg (8.2 lb)

10%

Product specificaties

Merk:	Apc
Categorie:	Niet gecategoriseerd
Model:	Line-R LSW1200-IND
Kleur van het product:	Zwart
Ingebouwd display:	Nee
Gewicht:	3050 g
Breedte:	210 mm
Diepte:	132 mm
Hoogte:	110 mm
Geluidsniveau:	40 dB
Gewicht verpakking:	3050 g
Gebruikershandleiding:	Ja
LED-indicatoren:	Ja
Afmetingen verpakking (BxDxH):	132 x 210 x 110 mm
Duurzaamheidscertificaten:	CE, China RoHS, REACH, RoHS
Uitgangsvermogen:	600 W
Temperatuur bij opslag:	-20 - 50 °C
Stroomspanning bescherming:	Overspanningsbeveiliging
Frequentie:	50/60 Hz
Luchtvochtigheid bij opslag:	0 - 90 procent
Spanning:	230 V
Hoogte, in bedrijf:	0 - 1015.9 m
Hoogte bij opslag:	0 - 1015.9 m
Bedrijfstemperatuur (T-T):	0 - 40 °C
Relatieve vochtigheid in bedrijf (V-V):	0 - 90 procent
Surge energy rating:	148 J
Aantal AC uitgangen:	3 AC-uitgang(en)
Nominale input voltage:	230 V
Stopcontacttypes:	CEE
Spanningsbeveiliging:	Ja
Garantieperiode:	2 jaar
Type indicator:	LED