Apc ER7SHELFS Handleiding

Apc Niet gecategoriseerd ER7SHELFS

Lees hieronder de 📖 handleiding in het Nederlandse voor Apc ER7SHELFS (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 23 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

Installation 990–91513 Release date: 02/2021

Easy Rack Accessory Short Shelf Kit ER7SHELFS

Kit Instructions

The 1U, Accessory Short Shelf can be installed to the vertical mounting rails in an

empty space in the Easy Rack to support your equipment.

ER7SHELFS Inventory Tools Required (not provided)

Shelf (1)

Torx® wrench

M6 x 12 Pan Head T30 Screw (8) Cage nut tool

Cage Nut M6 14/16 SWG (8)

Proper location in the rack for the cage nuts:

ns0014a

1. Locate the top and bottom U space on the vertical

mounting rails. Every third hole on the mounting rails

is numbered to indicate the middle of a U space.

2. Install the cage nuts on the interior of the vertical

mounting rail; then install the shelf.

CAUTION

FALLING EQUIPMENT HAZARD

Do NOT install cage nuts vertically with the tabs engaging the top and bottom of

the square hole.

Failure to follow these instructions can result in injury or equipment

damage.

APC by Schneider Electric

70 Mechanic Street

02035 Foxboro, MA

USA

www.apc.com

As standards, specifications, and design

change from time to time, please ask for

confirmation of the information given in this

publication.

reserved.

Easy Rack Accessory Short Shelf Kit ER7SHELFS

Proper installation position for the cage nuts:

ns1768a

• Install cage nuts horizontally, with the tabs engaging

the sides of the square hole.

• Install the cage nuts on the interior of the vertical

mounting rail.

Install the cage nut:

gen0188a

1. From the inside of the rack, insert the cage nut into the

square hole.

2. Hook one tab of the cage nut assembly through the far

side of the hole.

3. Place the cage nut tool on the other side of the cage

nut and pull to snap into position.

Remove the cage nut:

1. Remove any attached screw.

2. Grasp the cage nut, squeeze the tabs on the sides, and push to release it from the square hole.

Shelf Dimensions:

The Shelf has sliding rails which are adjustable from the minimum of 390mm (15.35 in.) when

retracted and maximum of 650mm (25.59 in.) when fully extended.

Adjust the rails:

To extend the adjustable rails of the shelf:

1. Remove the four (4) M6 x 12 pan head T30

screws.

2. Pull the rails out to the dimension you

require.

3. Install the four (4) M6 x 12 pan head T30

screws to secure the rails in their new

location to the shelf.

Install the shelf:

Install four (4) cage nuts to the front two vertical mounting rails as described above. Install four (4)

cage nuts to the inside of the rear vertical mounting rails as described above.

At the front of the rack, attach four (4) screws to the front of the shelf and into the four (4) cage nuts

you installed in the vertical mounting rails.

At the rear of the rack, install four (4) screws to the rails on the rear of the shelf and through the four

(4) cage nuts installed in the vertical mounting rails. The illustration below shows this installation

process.

ns3209a

Front of rack Rear of rack

The Easy Racks in the illustration above are shown without doors or side panels for clarity.

2 990–91513

Product specificaties

Merk:	Apc
Categorie:	Niet gecategoriseerd
Model:	ER7SHELFS
Kleur van het product:	Zwart
Gewicht:	4000 g
Breedte:	485 mm
Diepte:	392 mm
Hoogte:	32 mm
Breedte verpakking:	580 mm
Diepte verpakking:	480 mm
Hoogte verpakking:	110 mm
Soort:	Rekschap
Maximale gewichtscapaciteit:	50 kg
Aantal per verpakking:	1 stuk(s)
Maat:	19 "
Rackcapaciteit:	1U
Code geharmoniseerd systeem (HS):	85389099