Antari F-80 Handleiding
Antari
Effect machine
F-80
Lees hieronder de đź“– handleiding in het Nederlandse voor Antari F-80 (15 pagina's) in de categorie Effect machine. Deze handleiding was nuttig voor 81 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/15
1
User Manual
Antari Fog Machine
Congratulations on the purchase of your new
ANTARI FOG MACHINE.
Introduction
Thank you for choosing an ANTARI Fog Machine. You now own a rugged and powerful
state-of-the-art machine. Prior to use, we suggest that you carefully read all of the
instructions. By following the suggestions found in this user manual, you can look forward to
the reliable and satisfactory performance of your ANTARI Fog Machine for years to come.
Please follow these operation, safety and maintenance instructions to
ensure a long and safe life for your fog machine.
Cautions
Danger of electric shock
♦ Keep this device dry.
♦ For inside use only. Not designed for outside use.
♦ For the 110V models, use 3-prong grounded electrical outlet only. Prior to use take care
to determine that the unit is installed at the rated voltage.
♦ Always unplug your ANTARI Fog Machine before filling its tank.
♦ Keep fog machine upright.
♦ Turn off or unplug when not in use.
♦ This machine is not water- or splash-proof. If moisture, water, or fog liquid gets inside the
housing, immediately unplug the unit and contact a service technician or your ANTARI
dealer before using it again.
♦ No user serviceable parts inside. Refer to your ANTARI dealer or other qualified service
personnel.
Danger of burns
♦ For adult use only. Fog machine must be installed out of the reach of children. Never
leave the unit running unattended.
♦ Never aim the output nozzle directly at people.
♦ Fog machine output is very hot. Avoid coming within 60 cm of the output nozzle during
operation.
♦ Locate the fog machine in a well-ventilated area. Never cover the unit’s vents. In order to
guarantee adequate ventilation, allow a free air space of at least 20 cm around the sides
and top of the unit.
♦ Never aim the output nozzle at open flames.
♦ The output nozzle becomes very hot during operation (300 degrees C). Keep flammable
materials at least 50 cm away from the nozzle.
♦ Always allow your ANTARI Fog Machine to cool down before attempting to clean or
service it.
Danger of explosion
♦ Never add flammable liquids of any kind (oil, gas, perfume) to the fog liquid.
2
Pay attention to all warning labels and instructions printed on the exterior of your ANTARI
Fog Machine
♦ Use only the high-quality, water-based fog liquid that your dealer recommends. Other fog
liquids may cause clogging or “spitting”.
♦ Always make sure there is sufficient liquid in the fog liquid tank. Operating this unit
without liquid will cause damage to the pump as well as over-heating of the heater.
♦ If your ANTARI Fog Machine fails to work properly, discontinue use immediately. Drain all
fog liquid from the tank, pack the unit securely (preferably in the original packing material),
and return it to your ANTARI dealer for service.
♦ Always drain tank before mailing or transporting this unit.
♦ Never drink fog liquid. If it is ingested, call a doctor immediately. If fog liquid comes in
contact with skin or eyes, rinse thoroughly with water.
Unpacking & Inspection
Open the shipping carton and verify that all equipment necessary to operate the system has
arrived intact. Refer to the “Features” section for information on what items are included with
your model. If any equipment is missing contact your ANTARI dealer immediately.
Before beginning initial setup of your ANTARI Fog Machine, make sure that there is no
evident damage caused by transportation. In the event that the unit’s housing or cable is
damaged, do not plug it in and do not attempt to use it until after contacting your ANTARI
dealer for assistance.
Setup
♦ Remove all packing materials from shipping box. Check that all foam and plastic padding
is removed, especially in the nozzle area.
♦ Place fog machine on a flat surface and remove fog liquid tank cap.
♦ Fill with ANTARI Fog Liquid or other high-quality water-based fog fluid. Any other types of
fluid can damage the unit. When filled, place cap back on liquid tank.
♦ Firmly attach the remote control cable to the proper input on the rear of the machine.
Operation
♦ Plug power cord into a grounded electrical outlet. If necessary, turn power switch on rear
of unit to “ON” position. Warm-up is complete when green lamp lights up on remote unit.
♦ To emit fog, press the appropriate button on the remote for the desired length of time.
♦ The remote unit’s lamp will cycle on and off as the machine re-heats to the proper
operating temperature.
♦ For further information on operating your ANTARI Fog Machine, see the section titled,
“Remote Control Operation”.
If your model includes a mounting bracket designed for overhead installation, it may be
installed at floor level or suspended overhead. If the unit is to be mounted using the bracket,
it is important that the fog does not shoot directly at any one’s face. Whatever installation
method you choose, do not allow the unit to have more than a 15 degree angle of inclination.
Important: Always monitor tank fluid level as you are fogging. Running a fog machine with
no fluid can permanently damage the unit.
3
If you experience low output, pump noise or no output at all, unplug immediately. Check fluid
level, the external fuse, remote connection, and power from the wall. If all of the above
appears to be O.K., plug the unit in again. If fog does not come out after holding the remote
button down for 30 seconds, check the hose attached to the tank to make sure there is fluid
going through the hose. If you are unable to determine the cause of the problem, do not
simply continue pushing the remote button, as this may damage the unit. Return the
machine to your ANTARI dealer.
Remote Control Operation
♦ FC-1: 10 meter wired remote controller with three-prong plug for ANTARI Fog Machine
models F-150, F-250 and F-350. When the fog machine has reached operating
temperature the lamp on this remote control will light up, indicating that the operator may
begin fog emission by pressing the red button. Lamp turns off during fog machine warm-
up (approx. 4 minutes) and re-heating cycles (approx. 1-2 minutes), and turns on when
the machine becomes operational.
♦ FC-2: 10 meter wired multi-function remote controller with 5-pin XLR connector for
ANTARI Fog Machine models F-450, F-550, F-560 and F-750. Its three knobs allow the
operator to customize fog machine functions by adjusting fogging duration, interval and
volume. Press the yellow TIMERS button to activate the timer function. Adjust the
interval between each fog emission (within the range of 10 seconds to 5 minutes) by
means of the INTERVAL control knob. Adjust the duration of each fog emission (within
the range of 1 to 10 seconds) by means of the DURATION control knob. When pressed,
the green MANUAL button overrides all other function controls, and activates maximum
output. Press the red CONTINUOUS button for continuous output. Adjust output volume
with the OUTPUT knob.
♦ FC-3: Wireless remote controller with 5-pin XLR connector for ANTARI Fog Machine
models F-450, F-550, F-560 and F-750. Attach the receiver’s magnetic base to the fog
machine. Plug the receiver’s cable into the fog machine’s socket. Using the sending unit,
your ANTARI Fog Machine can be operated from a distance of up to 50 meters. Dip
switches inside the receiver can be configured to allow control of up to three ANTARI Fog
Machines. By means of the dip switches, adjust the receiver on each fog machine to a
different transmission frequency. The first three buttons on the sending unit allow the
operator to independently control each fog machine, while the fourth button enables
simultaneous control of all three machines.
♦ FC-6: 10 meter wired remote controller with ¼” stereo plug for ANTARI Fog Machine
model F-120. See operating instructions for the FC-1 controller.
♦ FC-7: Wireless remote controller with ¼” stereo plug for ANTARI Fog Machine model F-
120. Remote operation is possible up to a distance of 50 meters.
♦ FC-8: 10 meter wired remote controller with ¼” stereo plug for ANTARI Fog Machine
model F-120. Its two knobs allow the operator to customize fog machine functions by
adjusting output duration and interval. Press the yellow TIMERS button to activate the
timer function. Adjust the interval between each fog emission (within the range of 10
seconds to 5 minutes) by means of the INTERVAL control knob. Adjust the duration of
each fog emission (within the range of 1 to 10 seconds) by means of the DURATION
control knob. When pressed, the green MANUAL button overrides all other function
controls, and activates maximum output. Press the red CONTINUOUS button for
continuous output.
Cleaning your fog machine regularly will help reduce costly parts
replacement and repair charges.
Product specificaties
| Merk: | Antari |
| Categorie: | Effect machine |
| Model: | F-80 |
Heb je hulp nodig?
Als je hulp nodig hebt met Antari F-80 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Effect machine Antari
23 Augustus 2024
8 November 2023
2 Juli 2023
29 Juni 2023
22 Juni 2023
21 Juni 2023
19 Juni 2023
18 Juni 2023
16 Juni 2023
12 Juni 2023
Handleiding Effect machine
- Effect machine BeamZ
- Effect machine Behringer
- Effect machine Boss
- Effect machine HQ
- Effect machine HQ Power
- Effect machine Konig
- Effect machine Manta
- Effect machine Martin
- Effect machine Max
- Effect machine Midas
- Effect machine Monacor
- Effect machine Nedis
- Effect machine Pyle
- Effect machine Showtec
- Effect machine Velleman
- Effect machine Viking
- Effect machine Westinghouse
- Effect machine JB Systems
- Effect machine Monoprice
- Effect machine NGS
- Effect machine Steren
- Effect machine Eurolite
- Effect machine American DJ
- Effect machine Chauvet
- Effect machine QTX
- Effect machine Valcom
- Effect machine Karma
- Effect machine Adj
- Effect machine Elation
- Effect machine Valueline
- Effect machine Fredenstein
- Effect machine TC Electronic
- Effect machine Elysia
- Effect machine Stairville
- Effect machine Black Lion Audio
- Effect machine Laserworld
- Effect machine TCM FX
- Effect machine Drawmer
- Effect machine ColorKey
- Effect machine Evo-Lite
- Effect machine Blizzard
- Effect machine Hazebase
- Effect machine IGS Audio
- Effect machine Cameo
- Effect machine Sagitter
- Effect machine DJPower
- Effect machine Doepfer
- Effect machine Fun Generation
- Effect machine Lotronic
- Effect machine IMG Stage Line
- Effect machine Lexicon
- Effect machine Futurelight
- Effect machine The Confetti Maker
- Effect machine Eliminator Lighting
- Effect machine BoomTone DJ
- Effect machine Klark Teknik
- Effect machine Lab Gruppen
- Effect machine Audibax
- Effect machine Magmatic
- Effect machine Technical Pro
- Effect machine Rosco
- Effect machine Showven
Nieuwste handleidingen voor Effect machine
30 November 2024
20 November 2024
19 November 2024
16 November 2024
15 November 2024
7 November 2024
7 November 2024
7 November 2024
7 November 2024
7 November 2024