Amtrol Therm-X-Trol ST-1 Handleiding

Amtrol Ketel & boiler Therm-X-Trol ST-1

Lees hieronder de 📖 handleiding in het Nederlandse voor Amtrol Therm-X-Trol ST-1 (2 pagina's) in de categorie Ketel & boiler. Deze handleiding was nuttig voor 28 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

READ CAREFULLY THE

PRODUCT INSTALLATION,

OPERATING AND MAINTENANCE MANUAL.

FAILURE TO FOLLOW THE INSTRUCTIONS AND

WARNINGS IN THE MANUAL MAY RESULT IN

SERIOUS OR FATAL INJURY AND/OR PROPERTY

DAMAGE, AND WILL VOID THE PRODUCT

WARRANTY. THIS PRODUCT MUST BE

INSTALLED BY A LICENSED PROFESSIONAL.

FOLLOW ALL APPLICABLE LOCAL AND STATE

CODES AND REGULATIONS, IN THE ABSENCE

OF SUCH CODES, FOLLOW THE CURRENT

EDITIONS OF THE NATIONAL PLUMBING CODE

AND NATIONAL ELECTRIC CODE,

AS APPLICABLE.

This Product, like most

Products under pressure,

may over time corrode, weaken and burst or explode,

causing serious or fatal injury, leaking or flooding and/

or property damage. To minimize risk, a licensed

professional must install and periodically inspect and

service the product. A drip pan connected to an

adequate drain must be installed if leaking or flooding

could cause property damage. Do not locate in an

area where leaking could cause property damage to

the area adjacent to the appliance or to lower floors

of the structure.

The recurrence of pressure

buildup may indicate that this

unit is in need of replacement. Operating a plumbing

system in this condition presents the risk of damage

and leaks.

RUPTURE OR EXPLOSION

HAZARD. Do not expose

Product to freezing temperatures or water

temperatures in excess of . Failure to properly 140°F

size the product or follow these instructions may

result in excessive strain on the system and may lead

to product failure, serious or fatal personal injury,

leakage and/or property damage. USE ONLY WITH

RESIDENTIAL POTABLE WATER SYSTEMS.

A relief valve must be

installed to prevent pressure

in excess of local code requirement or maximum

working pressure of 150 psig, whichever is less. At

least once every 3 years or if discharge is present, a

licensed professional should inspect the temperature

and pressure relief valve and replace if corrosion is

evident or the valve does not function. FAILURE TO

INSPECT THIS VALVE AS DIRECTED COULD

RESULT IN UNSAFE TEMPERATURE OR

PRESSURE BUILD-UP WHICH CAN RESULT IN

PRODUCT FAILURE, SERIOUS INJURY OR

DEATH AND/OR SEVERE PROPERTY DAMAGE

AND VOID THE PRODUCT WARRANTY.

Chlorine & Aggressive

Water: The water quality can

significantly influence the life of this product. You

should test for corrosive elements, acidity, total solids

and other relevant contaminants, including chlorine

and treat your water appropriately to insure

satisfactory performance and prevent premature

failure.

NOTE: Inspect for shipping damage. Notify freight carrier or store where purchased immediately if damage is

present. To avoid risk of personal injury and property damage, if the product appears to be malfunctioning or shows

signs of corrosion, call a qualified professional immediately. Current copies of the product manual can be viewed at

www.amtrol.com. Use proper safety equipment when installing.

THIS IS THE SAFETY ALERT SYMBOL. IT IS USED TO ALERT YOU TO POTENTIAL PERSONAL

INJURY AND OTHER HAZARDS. OBEY ALL SAFETY MESSAGES THAT FOLLOW THIS SYMBOL

TO REDUCE THE RISK OF PERSONAL INJURY AS WELL AS PROPERTY DAMAGE.

Model ST-1

THERMAL EXPANSION TANK

FOR POTABLE WATER

INSTALLATION & OPERATION INSTRUCTIONS

Application

The ST-1 expansion tank is for use on tankless,

residential on-demand water heaters with a total

water content of 2 gallons or less and a maximum

set point of 140°F. Do not use with larger storage-

type water heaters, as these will exceed the

capacity of the ST-1.

Installation

1. Install the expansion tank on the cold water

supply line to the water heater at a point

between the water heater and backflow

preventer or other one-way device (Figure 1).

2. Once the expansion tank is installed, check

the cold water supply line for any leakage.

Make repairs if necessary.

3. Before the initial firing of the water heater,

open a hot water fixture and draw for one

minute to purge air. Next, close and open the

fixture in 30 second intervals, repeating three

thimes to flush the tank and piping.Finally,

turn the water heater temperature control to

desired ending temperature (see water heater

instructions). Do not set temperature higher

than the expansion tank maximum.

4. To relieve initial thermal expansion, slightly

open a hot water faucet. Continue until water

heater temperature is satisfied. Once heater is

at its operating range, no further bleeding of

expanded water is required.

5. The water heater and expansion tank will

now be operational. The expansion tank

will control pressure increases caused by

thermal expansion to a level below the water

heater relief valve setting. FOR USE ON

TANKLESS RESIDENTIAL ON DEMAND

WATER HEATERS WITH A TOTAL WATER

CONTENT OF 2 GALLONS OR LESS AND

A MAXIMUM SET POINT OF 140° F. NON-

ADJUSTABLE PRECHARGE.

PSI Volume (cu.in.) Weight (lb.)

.00 0.00 .87

20.00 3.92 1.01

40.00 5.77 1.07

60.00 7.43 1.13

80.00 8.17 1.16

100.00 8.63 1.18

120.00 9.00 1.19

140.00 9.27 1.20

150.00 9.27 1.20

Maintenance

A licensed professional should check the

complete system, including the expansion tank,

yearly and more frequently as the system ages.

Warranty

ST-1 Model: Seven (7) Year Limited Warranty

Visit www.amtrol.com for complete warranty

details.

PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY

IMPORTANT GENERAL SAFETY INFORMATION -

ADDITIONAL SPECIFIC SAFETY ALERTS APPEAR IN THE FOLLOWING INSTRUCTIONS.

1400 Division Road, West Warwick, RI 02893 USA

T: 800.426.8765 www.amtrol.com

One or more features of this product are covered by U.S. patents, visit www.amtrol.com/patents for more information.

Figure 1. Typical Installation

ST-1

Thermal

Expansion Tank

Hot Water

T & P

Relief

Valve

Cold

Water

Supply

Backflow Preventor

Check Valve or

Pressure Reducing Valve

Water

Heater

Product specificaties

Merk:	Amtrol
Categorie:	Ketel & boiler
Model:	Therm-X-Trol ST-1

Heb je hulp nodig?

Als je hulp nodig hebt met Amtrol Therm-X-Trol ST-1 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Ketel & boiler Amtrol

Amtrol Extrol SX-130V Handleiding

29 Juli 2023

Amtrol Extrol EX-30 Handleiding

28 Juli 2023

Amtrol Extrol Pro EX-15PRO Handleiding

28 Juli 2023

Amtrol Extrol SX-40V Handleiding

28 Juli 2023

Amtrol Extrol SX-30V Handleiding

28 Juli 2023

Amtrol Extrol EX-90 Handleiding

28 Juli 2023

Amtrol Therm-X-Trol ST-200V Handleiding

28 Juli 2023

Amtrol Therm-X-Trol ST-12 Handleiding

28 Juli 2023

Amtrol Extrol SX-110V Handleiding

28 Juli 2023

Amtrol Therm-X-Trol ST-60V Handleiding

28 Juli 2023

Handleiding Ketel & boiler

Nieuwste handleidingen voor Ketel & boiler

Midea D80-20ED6 Handleiding

14 December 2024

Midea MWH-180ECNCR Handleiding

11 December 2024

Midea MWH-130ECNCR Handleiding

11 December 2024

Gorenje TGR50MNGU Handleiding

10 December 2024

Haier HP80M5 Handleiding

10 December 2024

Haier HP110M5 Handleiding

10 December 2024

Haier Q-B-J-1-151/2.49/0.05-W/N Handleiding

10 December 2024

Haier Q-B-J-1-141/2.24/0.05-W/N Handleiding

10 December 2024

Haier Q-B-J-1-175/2.48/0.05-D/SX Handleiding

10 December 2024

Haier Q-B-J-1-185/3.00/0.05-D/A6 Handleiding

10 December 2024