Air King BFQL50 Handleiding

Air King Afzuigkap BFQL50

Lees hieronder de 📖 handleiding in het Nederlandse voor Air King BFQL50 (12 pagina's) in de categorie Afzuigkap. Deze handleiding was nuttig voor 27 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/12

IMPORTANT INSTRUCTIONS -

OPERATING MANUAL

SAVE THESE INSTRUCTIONS

www.airkinglimited.com

6727919 Rev. H 4-20 1 of 12

Exhaust Fan

Models: BFQL50, BFQL70, BFQL120

READ AND SAVE THESE INSTRUCTIONS

READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL, OPERATE OR MAINTAIN

THE PRODUCT DESCRIBED. PROTECT YOURSELF AND OTHERS BY OBSERVING ALL SAFETY

INFORMATION. FAILURE TO COMPLY WITH INSTRUCTIONS COULD RESULT IN PERSONAL

INJURY AND/OR PROPERTY DAMAGE!

RETAIN INSTRUCTIONS FOR FUTURE REFERENCE.

GENERAL SAFETY INFORMATION

When using electrical appliances, basic precautions should

always be followed to reduce the risk of ﬁre, electric shock and

injury to person, including the following:

WARNING: TO REDUCE THE RISK

OF FIRE, ELECTRIC SHOCK AND INJURY TO

PERSON, OBSERVE THE FOLLOWING:

a) Use this unit only in the manner intended by the manufacturer.If you have

questions, contact the manufacturer.

b) Before servicing or cleaning the unit, switch power off at service

panel and lock the service disconnecting means to prevent power

from being switched on accidentally. When the service disconnecting

means cannot be locked, securely fasten a prominent warning

device, such as a tag, to the service panel.

WARNING: TO REDUCE THE RISK

OF FIRE, ELECTRIC SHOCK AND INJURY TO

PERSON, OBSERVE THE FOLLOWING:

a) Installation work and electrical wiring must be done by qualiﬁed

person(s) in accordance with all applicable codes and standards,

including ﬁre-related construction.

b) Sufﬁcient air is needed for proper combustion and exhausting of

gases through the ﬂue (chimney) of fuel burning equipment to prevent

back drafting. Follow the heating equipment manufacturer’s guideline

and safety standards such as those published by the National Fire

Protection Association (NFPA) and the American Society for Heating,

Refrigeration, and Air Conditioning Engineers (ASHRAE), and the local

code authorities.

c) When cutting or drilling into wall or ceiling, do not damage electrical

wiring and other hidden utilities.

CAUTION: FOR GENERAL VENTILATING USE ONLY.

DO NOT USE TO EXHAUST HAZARDOUS OR EXPLOSIVE

MATERIALS AND VAPORS.

d) Ducted fans must always be vented to the outdoors.

e) If this unit is to be installed over a tub or shower, it must be marked

as appropriate for the application and be connected to a GFCI (Ground

Fault Circuit Interrupter) – protected branch circuit.

f) This unit must be grounded.

g) To avoid motor bearing damage and noisy and/or unbalanced impellers,

keep drywall spray, construction dust, etc. off power unit.

h) Read all instructions before installing or using exhaust fan.

i) Suitable for use with electronic speed control device.

WARNING: DO NOT USE IN KITCHENS.

WARNING: THE DUCTING FROM THIS FAN TO THE

OUTSIDE OF THE BUILDING HAS A STRONG EFFECT

ON THE AIR FLOW, NOISE AND ENERGY USE OF THE FAN. USE

THE SHORTEST, STRAIGHTEST DUCT ROUTING POSSIBLE FOR

BEST PERFORMANCE, AND AVOID INSTALLING THE FAN WITH

SMALLER DUCTS THAN RECOMMENDED. INSULATION AROUND

THE DUCTS CAN REDUCE ENERGY LOSS AND INHIBIT MOLD

GROWTH. FANS INSTALLED WITH EXISTING DUCTS MAY NOT

ACHIEVE THEIR RATED AIRFLOW.

INSTALLATION INSTRUCTIONS

CAUTION: MAKE SURE POWER IS SWITCHED OFF

AT SERVICE PANEL BEFORE STARTING INSTALLATION.

SECTION 1

Preparing the Exhaust Fan

1. Unpack fan from the carton and conﬁrm that all pieces are present. In

addition to the exhaust fan you should have:

1 - Grill with Light Lens

1 - Damper Assembly (attached)

1 - Mounting Bracket

1 - LampLED

1 - Hardware Bag

1 - Electrical Connector

4 - Wire Nuts

1 - Instruction/Safety Sheet

2. Remove the wire compartment cover and store in the carton until

needed so it does not get damaged or lost (Figure 1).

3. Choose the location for your fan. To ensure the best air and sound

performance, it is recommended that the length of ducting and the

number of elbows be kept to a minimum, the radius of each elbow be

as large as possible for the installation, and that insulated hard ducting

be used. Larger duct sizes will reduce noise

and airﬂow restrictions.

4. Select the most convenient electrical

knockout and remove using a straight-

blade screw driver (Figure 2).

5. No additional vibration deadening materials

are needed for this fan.

SECTION 2

New Construction

1. Using the gauge on the mounting bracket, line up the bracket on the

joist so the bottom of the fan will be ﬂush with the ﬁnished ceiling.

Nail or screw the bracket in place securely (Figure 3).

2. Snap the fan body into the bracket The fan can be (Figure 4).

snapped into position with the duct collar facing to the left or the right

depending which is most convenient.

www.airkinglimited.com

6727919 Rev. H 4-20 2 of 12

SECTION 3

Existing Construction

1. Position housing against the joist or stud and trace an outline of the

housing onto the ceiling/wall material. Set housing aside and cut

opening, being careful not to cut or damage any electrical or other

hidden utilities (Figure 5).

2. Line up the bracket on the joist so the bottom of the fan will be ﬂush

with the ﬁnished ceiling. Nail or screw the snap-in bracket in place

securely (Figure 3).

3. Snap the fan body into the bracket The fan can be (Figure 4).

snapped into position with the duct collar facing to the left or the right

depending which is most convenient.

SECTION 4

Ducting

NOTE: 4" OR LARGER RIGID DUCT IS RECOMMENDED FOR BEST

PERFORMANCE.

CAUTION: ALL DUCTING MUST COMPLY WITH LOCAL

AND NATIONAL BUILDING CODES.

1. Connect the ducting to the fan’s duct collar Secure in place (Figure 6).

using tape or screw clamp. Always duct the fan to the outside through

a wall or roof cap. It is recommended that low restriction termination

ﬁttings be used.

Figure 2

Figure 3

Figure 4

Figure 5

Figure 6

Figure 1

2. Ensure duct joints and exterior penetrations are sealed with caulk or

other similar material to create an air-tight path to minimize building

heat loss or gain and to reduce the potential for condensation. Place/

wrap insulation around duct and/or fan to in order to minimize

possible condensation buildup within the duct, as well as building heat

loss or gain (Figure 7).

SECTION 5

Wiring

CAUTION: MAKE SURE POWER IS SWITCHED OFF

AT SERVICE PANEL BEFORE STARTING INSTALLATION.

CAUTION: ALL ELECTRICAL CONNECTIONS

MUST BE MADE IN ACCORDANCE WITH LOCAL

CODES, ORDINANCES, OR NATIONAL ELECTRICAL CODE. IF YOU ARE

UNFAMILIAR WITH METHODS OF INSTALLING ELECTRICAL WIRING,

SECURE THE SERVICES OF A QUALIFIED ELECTRICIAN.

1. Wiring Fan/Light Independently: Run wiring from an approved wall

switch carrying the appropriate rating. One neutral (white), one ground

(green or bare copper), and two hot (black lead connected to the switch).

Secure the electrical wires to the housing with an approved electrical

connector. Make sure you leave enough wiring in the box to make the

connection to the fan’s receptacle.

1a. From where you have access to inside the fan’s junction box, connect

the one white wire from the house to both the white wire from the

fan’s light receptacle and the white wire from the fan’s exhaust

receptacle. Connect the ﬁrst black wire from the wall switch to the

black wire from the fan’s light receptacle. Connect the second black

wire from the switch to the fan’s exhaust receptacle. Connect

the ground wire from the house to the green wire from the fan’s

receptacle (Figure 8). Use approved methods for all connections.

www.airkinglimited.com

6727919 Rev. H 4-20 3 of 12

2. Wiring Fan/Light together: Run wiring from an approved wall switch

carrying the appropriate rating. One neutral (white), one ground (green

or bare copper), and one hot (black lead connected to the switch).

Secure the electrical wires to the housing with an approved electrical

connector. Make sure you leave enough wiring in the box to make the

connection to the fan’s receptacle.

2a. From where you have access to inside the fan’s junction box, connect

the one white wire from the house to both the white wire from the

fan’s light receptacle and the white wire from the fan’s exhaust

receptacle. Connect the black wire from the wall switch to both the

black wire from the fan’s light receptacle and the black wire from the

fan’s exhaust receptacle. Connect the ground wire from the house to

the green wire from the fan’s receptacle Use approved (Figure 9).

methods for all connections.

SECTION 6

Completing the Installation

1. Use a sealant appropriate for contact with the building materials

present and for the temperature requirements of the installation to

prevent air leakage from unconditioned spaces is recommended. If

gaps between unit housing and ceiling are great, additional material

(backing rod, ceiling material) may be required.

NOTE: This fan is rated for direct insulation contact (Type IC) and it is

recommended that this fan be completely covered by insulation in order to

reduce heat loss or gain to unconditioned space.

2. Reinstall the fan’s wire compartment cover. Rotate the blower wheel

by hand to ensure it spins freely. Plug the fan’s quick connect motor

cord into the receptacle. This cord will only ﬁt one way into the

receptacle (Figure 10).

NOTE: If using this fan to meet ASHRAE 62.2 requirements, locate the label

inside the fan housing and ﬁll in the appropriate information.

3. Install the grill/lens/light reﬂector, by ﬁrst removing the lens from the

grill (there are two tabs on either side that hold the lens in place).

Then remove the acorn nut and the lock washer which are installed

on the reﬂector mounting bolt in the fan housing. Adjust the height

of the reﬂector mounting bolt so that the grill will be tight up against

the ﬁnished ceiling and less than 1/4” of the reﬂector mounting bolt

protrudes through the reﬂector. Secure the reﬂector bolt’s position by

tightening the factory installed nut against the motor clip (Figure 11).

Figure 10

Figure 7

Insulation*

(place around and

over Fan Housing

Fan Housing

Power Cable*

Seal gaps

around Housing

Round

Duct*

Seal duct joints

with tape

Round

Elbows*

Wall Cap*

Roof Cap*

(with built-in

damper)

Keep duct

runs short

*Purchase separately

Figure 8

Supply from house

Black

Neutral (White)

Ground (Green or Bare)

Fan

Neutral (White)

Green

Black

By others

Red Black

Neutral (White)

Figure 9

Supply from house

Black

Neutral (White)

Ground (Green or Bare)

Fan

Neutral (White)

Green

Black

By others

Red

Neutral (White)

Product specificaties

Merk:	Air King
Categorie:	Afzuigkap
Model:	BFQL50

Heb je hulp nodig?

Als je hulp nodig hebt met Air King BFQL50 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Afzuigkap Air King

Air King Granada Handleiding

16 Oktober 2024

Air King FRAK80H Handleiding

3 September 2024

Air King LIN46md-900 Handleiding

18 Augustus 2024

Air King FRAS70 Handleiding

18 Augustus 2024

Air King AK100LS6 Handleiding

18 Augustus 2024

Air King BFQ50 Handleiding

18 Augustus 2024

Air King BFC90H Handleiding

18 Augustus 2024

Air King BFQL70 Handleiding

18 Augustus 2024

Air King LIN34md-900 Handleiding

18 Augustus 2024

Air King LIN34m-900 Handleiding

18 Augustus 2024

Handleiding Afzuigkap

Nieuwste handleidingen voor Afzuigkap

Miele DA 6520 D Handleiding

21 November 2024

Miele DA 420-4 Handleiding

21 November 2024

Miele DA 2906 EXT Handleiding

21 November 2024

Miele DA 2660 Handleiding

21 November 2024

XO R230W Handleiding

21 November 2024

Ilve AGK90 Handleiding

20 November 2024

Ilve AGQ90 Handleiding

20 November 2024

Ilve AGQ60 Handleiding

20 November 2024

Ilve AGQ120 Handleiding

20 November 2024

Ilve AGK120 Handleiding

20 November 2024