Air King AKZA200D Handleiding

Air King Afzuigkap AKZA200D

Lees hieronder de 📖 handleiding in het Nederlandse voor Air King AKZA200D (8 pagina's) in de categorie Afzuigkap. Deze handleiding was nuttig voor 28 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/8

IMPORTANT INSTRUCTIONS -

OPERATING MANUAL

SAVE THESE INSTRUCTIONS

www.airkinglimited.com

6727926 Rev. C 6-18 1 of 8

Exhaust Fan

AKZA200D, AKZA200D1

READ AND SAVE THESE INSTRUCTIONS

READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL, OPERATE OR MAINTAIN

THE PRODUCT DESCRIBED. PROTECT YOURSELF AND OTHERS BY OBSERVING ALL SAFETY

INFORMATION. FAILURE TO COMPLY WITH INSTRUCTIONS COULD RESULT IN PERSONAL

INJURY AND/OR PROPERTY DAMAGE!

RETAIN INSTRUCTIONS FOR FUTURE REFERENCE.

GENERAL SAFETY INFORMATION

When using electrical appliances, basic precautions should

always be followed to reduce the risk of ﬁre, electric shock and

injury to person, including the following:

WARNING: TO REDUCE THE RISK

OF FIRE, ELECTRIC SHOCK AND INJURY TO

PERSON, OBSERVE THE FOLLOWING:

a) Use this unit only in the manner intended by the manufacturer. If you have

questions, contact the manufacturer.

b) Before servicing or cleaning the unit, switch power off at service

panel and lock the service disconnecting means to prevent power

from being switched on accidentally. When the service disconnecting

means cannot be locked, securely fasten a prominent warning

device, such as a tag, to the service panel.

WARNING: TO REDUCE THE RISK

OF FIRE, ELECTRIC SHOCK AND INJURY TO

PERSON, OBSERVE THE FOLLOWING:

a) Installation work and electrical wiring must be done by qualiﬁed

person(s) in accordance with all applicable codes and standards,

including ﬁre-related construction.

b) Sufﬁcient air is needed for proper combustion and exhausting of

gases through the ﬂue (chimney) of fuel burning equipment to prevent

back drafting. Follow the heating equipment manufacturer’s guideline

and safety standards such as those published by the National Fire

Protection Association (NFPA) and the American Society for Heating,

Refrigeration, and Air Conditioning Engineers (ASHRAE), and the local

code authorities.

c) When cutting or drilling into wall or ceiling, do not damage electrical

wiring and other hidden utilities.

CAUTION: FOR GENERAL VENTILATING USE ONLY.

DO NOT USE TO EXHAUST HAZARDOUS OR EXPLOSIVE

MATERIALS AND VAPORS.

d) Ducted fans must always be vented to the outdoors.

e) This unit must be grounded.

f) To avoid motor bearing damage and noisy and/or unbalanced impellers,

keep drywall spray, construction dust, etc. off power unit.

g) Read all instructions before installing or using exhaust fan.

WARNING: TO REDUCE THE RISK OF FIRE,

ELECTRIC SHOCK, DO NOT USE THIS FAN WITH

ANY SOLID-STATE SPEED CONTROL DEVICE.

WARNING: DO NOT USE IN KITCHENS.

WARNING: THE DUCTING FROM THIS FAN TO THE

OUTSIDE OF THE BUILDING HAS A STRONG EFFECT

ON THE AIR FLOW, NOISE AND ENERGY USE OF THE FAN. USE

THE SHORTEST, STRAIGHTEST DUCT ROUTING POSSIBLE FOR

BEST PERFORMANCE, AND AVOID INSTALLING THE FAN WITH

SMALLER DUCTS THAN RECOMMENDED. INSULATION AROUND

THE DUCTS CAN REDUCE ENERGY LOSS AND INHIBIT MOLD

GROWTH. FANS INSTALLED WITH EXISTING DUCTS MAY NOT

ACHIEVE THEIR RATED AIRFLOW.

INSTALLATION INSTRUCTIONS

CAUTION: MAKE SURE POWER IS SWITCHED OFF AT

SERVICE PANEL BEFORE STARTING INSTALLATION.

SECTION 1

Preparing the Exhaust Fan

1. Unpack fan from the carton and conﬁrm that all pieces are present. In addition to the

exhaust fan you should have:

1 - Duct Adapter Panel

1 - Side Panel (attached)

1 - Damper Assembly (attached)

2 - Mounting Brackets

1 - Hardware bag

7 - Screws

4 - Nuts

1 - Instruction/Safety Sheet

2. Choose the location for your fan. To ensure the best air and sound performance, it is

recommended that the length of ducting and the number of elbows be kept to a minimum,

the radius of each elbow be as large as possible for the installation, and that insulated

hard ducting be used. This fan will require at least 12" of clearance in the ceiling or wall,

and will mount through drywall up to ½" thick. The fan mounts between 24" on center

joists using the provided mounting brackets.

3. No additional vibration deadening materials are needed for this fan.

SECTION 2

Determine Discharge

1. Determine if you will require the unit to exhaust vertically/horizontally or at a right angle

and install the included duct adapter panel accordingly, using the included screws

(Figure 1).

NOTE: In the right angle conﬁguration the air will enter the unit and ﬂow out the side at a 90°

angle. In the horizontal/vertical discharge conﬁguration, the air will enter the unit and ﬂow

directly out the other side.

2. Once the duct adapter panel is installed, using the same procedure as in Step 1, install

the side panel onto the open end of the housing (this will be dependent on how you

have chosen to exhaust the unit).

SECTION 3

Mounting to a Joist

1. If the mounting brackets are not already in place, install both brackets through the top

set of slots on the fan housing and secure in place with the four included nuts as shown.

Center the fan housing between the joists and secure the mounting brackets with screws

(not included) to the joist. Adjust the height of the housing so that it will be ﬂush with the

ﬁnished ceiling by loosening the mounting bracket nuts and sliding the housing up or

down on the bracket. Full tighten all four nuts to secure the housing in place (Figure 2).

www.airkinglimited.com

6727926 Rev. C 6-18 2 of 8

SECTION 4

Hanging Installation

1. If the mounting brackets are not already in place, install both brackets through the top

set of slots on the fan housing and secure in place with the four included nuts as shown.

Lift unit up onto the threaded rods and secure in place using appropriate hardware (not

included) (Figure 3).

SECTION 5

Ducting

CAUTION: ALL DUCTING MUST COMPLY WITH LOCAL AND

NATIONAL BUILDING CODES.

NOTE: To ensure quiet operation, at least 8 feet of insulated ﬂexible duct or insulated duct board

needs to be installed between the exhaust or supply grille(s) and the fan.

1. Before installing the ducting, make sure the fan’s 2 pin and 3 pin quick connect motor

cords are plugged into the corresponding receptacle located on the interior wire

compartment cover. These cords will only ﬁt one way into the receptacles .(Figure 4)

2. Connect the ducting to the fan’s duct collar Seal ducting to housing with (Figure 5).

appropriately rated tape. Use screws (rectangular duct) or suitable clamps (round duct)

to secure in place. Do not allow screws to interfere with operation of damper. Always

duct the fan to the outside through a wall or roof cap. It is recommended that low

restriction termination ﬁttings be used.

SECTION 6

Wiring

CAUTION: MAKE SURE POWER IS SWITCHED OFF AT

SERVICE PANEL BEFORE STARTING INSTALLATION.

CAUTION: ALL ELECTRICAL CONNECTIONS MUST BE

MADE IN ACCORDANCE WITH LOCAL CODES, ORDINANCES, OR

NATIONAL ELECTRICAL CODE. IF YOU ARE UNFAMILIAR WITH METHODS OF INSTALLING

ELECTRICAL WIRING, SECURE THE SERVICES OF A QUALIFIED ELECTRICIAN.

NOTE: This unit includes a side access panel for wiring that does not require the removal of the

fan’s blower assembly.

1. Remove the wire compartment cover screw and place cover in a secure place (Figure 6).

Figure 2 Bracket

Housing

Nut

Joist

Figure 3 Bracket

Housing

Nut

Threaded Rod

Figure 5 Housing

Ducting

Duct Collar

Right Angle

Discharge

Horizontal/

Vertical

Discharge

Figure 1

Duct

Adapter

Screws

Figure 4

2. Continuous Ventilation: For two speed fans wired for continuous ventilation, connect

the White wire of the fan to the White (Neutral) wire from the power source. Connect the

ground wire from the house to the green wire from the fan housing. Run 2 wires from a

properly grounded wall switch (not included) to the fan. Connect the Black wire of the fan

to the Black wire (Hot) from the power source. Connect the Hot Yellow wire from the fan

to the input of the switch. Connect the second Yellow wire from the fan to the output side

of the switch. Closing the switch will change from normal to high speed. Use (Figure 7).

approved methods for all connections.

2b. Intermittent Ventilation: For two speed fans wired for intermittent ventilation with a

standard duplex toggle switch (such as Leviton 5224-2W not included). Connect the White

wire of the fan to the White (Neutral) wire from the power source. Connect the ground wire

from the fan to the ground wire from the power source. Properly ground the switches.

Connect the black wire from the supply to one side of the top switch. Connect the black wire

from the fan to the other side of the top switch, Connect 1 yellow wire from the fan to each

side of the bottom switch. The top switch turns the fan On & Off, the bottom switch changes

speed between high and low Use approved methods for all connections. (Figure 8).

NOTE: Unit must be grounded according to all local and national codes.

3. Carefully tuck wire back inside wire compartment and replace wire compartment cover

securing with the screw that was removed earlier.

www.airkinglimited.com

6727926 Rev. C 6-18 3 of 8

SECTION 7

Completing the Installation

NOTE: When fan is mounted inline and no penetration is made into unconditioned spaces, there

is no need to use a sealant appropriate for contact with the building materials present and for

the temperature requirements of the installation to prevent air leakage from unconditioned

spaces. Additional material (backing rod, ceiling material) are also not required.

NOTE: This fan is rated for direct insulation contact (Type IC) and it is recommended that this fan

be completely covered by insulation in order to reduce heat loss or gain to unconditioned space.

1. Restore power and test your installation.

SECTION 8

Access Panel

1. This unit includes a hinged access panel. This allows access to the interior of the fan

once installed. To access the interior, unscrew the screws holding the panel in place

(Figure 9).

2. Reinstall the access panel by making sure the tabs are inserted into the slots on the

housing and pivoting the panel back towards the housing. Using the screws removed in

step 1, reattach the panel.

SECTION 9

Activating the Boost Speed

If your unit is equipped with a boost speed, and it is determined that additional ﬂow is necessary

due to excessive duct resistance or other ﬁeld conditions activate the boost speed by:

1. Find the 2 wire harness from the fan motor to the capacitor.

2. Disconnect the harness from the capacitor at the quick connect ﬁtting and remove the

“Boost Label” from the quick connect ﬁtting on the boost capacitor.

3. Plug the motor harness into the boost capacitor.

SECTION 10

Use and Care

CAUTION: MAKE SURE POWER IS SWITCHED OFF AT

SERVICE PANEL BEFORE SERVICING THE UNIT.

1. Cleaning the Fan Assembly: Wipe all parts with a dry cloth or gently vacuum the fan.

NEVER IMMERSE ELECTRICAL PARTS IN WATER.

CALIFORNIA RESIDENTS ONLY:

WARNING: THIS PRODUCT CAN EXPOSE YOU TO A CHEMICAL [OR

CHEMICALS] KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER.

WARNING: THIS PRODUCT CAN EXPOSE YOU TO A CHEMICAL

[OR CHEMICALS] KNOWN TO THE STATE OF CALIFORNIA TO CAUSE

REPRODUCTIVE TOXICITY.

Troubleshooting Guide

Trouble Probable Cause Suggested Remedy

1. Fan does not operate when the switch is on. 1a. A fuse may be blown or a circuit tripped. 1a. Replace fuse or reset circuit breaker.

1b. Connector plug from motor is not plugged in. 1b. Turn off power to unit. Remove Grill and plug motor into receptacle

in housing. Restore power to unit.

1c. Wiring is not connected properly. 1c. Turn off power to unit. Check that all wires are connected.

1d Motor has stopped operating. 1d. Replace motor.

2. Fan is operating, but air moves slower than normal. 2. Obstruction in the exhaust ducting. 2. Check for any obstructions in the ducting. The most common are bird

nests in the roof cap or wall cap where the fan exhausts to the outside.