Lincoln MKZ (2010) Handleiding

Lincoln Auto MKZ (2010)

Lees hieronder de 📖 handleiding in het Nederlandse voor Lincoln MKZ (2010) (13 pagina's) in de categorie Auto. Deze handleiding was nuttig voor 22 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/13
Erasing the Car2U Home Automation System buttons
Note: The system allows for three devices to be programmed. If you
need to change or replace any of the three devices after it has been
initially programmed, it will be necessary to erase the current settings
using the procedure below and then reprogramming all of the devices
being used.
To erase programming on the Car2U system (individual buttons cannot
be erased), use the following procedure:
1. Firmly press the two outside Car2U system
buttons simultaneously for approximately
20 seconds until the indicator lights begin to
blink rapidly. The indicator lights are located
directly above the buttons.
2. Once the indicator lights begin to blink,
release your fingers from the buttons. The
codes for all buttons are erased.
If you sell your vehicle equipped with the Car2U system, it is
recommended that you erase the programming for security reasons.
FCC and RSS-210 Industry Canada Compliance
The Car2U system complies with Part 15 of the FCC rules and with
RSS-210 of Industry Canada. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2)
This device must accept any interference received including interference
that may cause undesired operation.
Changes and modifications to the Car2U system transmitter by other
than an authorized service facility could void authorization to use the
equipment.
6
OUVRE-PORTE DE GARAGE UNIVERSEL (SELON L’ÉQUIPEMENT)
Votre véhicule peut être équipé d’une télécommande universelle pour porte
de garage qui peut être utilisé pour remplacer la télécommande classique.
Système d’automatisation domestique Car2U
MD
(selon l’équipement)
Le système d’automatisation domestique
Car2U
MD
est un émetteur universel situé dans
le rétroviseur du conducteur et qui comprend
deux fonctions principales : un ouvre-porte de
garage et une plate-forme pour activer à
distance une panoplie de dispositifs à
l’intérieur de votre domicile. Le système
d’ouvre-porte de garage Car2U
MD
remplace la télécommande portative
classique par un émetteur à trois boutons intégré à l’intérieur de votre
hicule. Une fois programmé pour les portes de garage, le système de
télécommande Car2U
MD
peut être programmé pour faire fonctionner les
dispositifs de curité et les systèmes d’éclairage domestiques.
AVERTISSEMENT : Assurez-vous d’éloigner toutes personnes
ou objets de la porte de garage ou du dispositif de sécurité que
vous devez programmer. Ne programmez jamais le système Car2U
MD
lorsque le véhicule est stationné dans un garage.
N’utilisez pas le système Car2U
MD
si vous possédez une commande
pour porte de garage qui n’est pas munie des dispositifs d’arrêt
automatique et de marche arrière tels que prescrits par les normes de
sécurité fédérales américaines. (Cette recommandation concerne aussi
les ouvre-portes de garage fabriqués avant le 1
er
avril 1982.)
Assurez-vous de conserver la télécommande d’origine pour l’utiliser avec
d’autres véhicules ou pour une programmation ultérieure du système
Car2U
MD
. Il est également recommandé, au terme de la vente ou du bail
de location du véhicule, de réinitialiser les boutons de commande du
système Car2U
MD
pour des raisons de sécurité. Consultez la rubrique
Effacement des boutons du système d’automatisation domestique
Car2U
MD
plus loin dans cette section.
Lisez toutes les instructions avant de tenter de programmer le système
Car2U
MD
. À cause des différentes étapes, il serait préférable d’obtenir
l’aide d’une autre personne pour programmer la télécommande.
Vous pouvez obtenir de l’information plus détaillée en ligne, sur le
système Car2U
MD
, au www.learcar2U.com ou en communiquant avec la
ligne d’aide Car2U
MD
au numéro sans frais 1-866-572-2728.
Commandes du conducteur
1
3. To input these positions into the Car2U
system, simultaneously press all three Car2U
system buttons for a few seconds and then
release to put the device into programming
mode. The indicator lights will blink slowly.
Within 2.5 minutes enter your corresponding
DIP switch settings from left to right into your
Car2U system by pressing and releasing the buttons corresponding to
the settings you circled.
4. After inputting switch settings, simultaneously press and release all
three Car2U system buttons. The indicator lights will turn on.
5. Press and hold the Car2U system button
you would like to use to control the garage
door. Immediately (within 1 second) release
the button once the garage door moves.
During this time the selected button indicator
light will blink slowly. Do not release the
button until you see the garage door move. Most garage doors open
quickly. You may need to hold the button from 5–55 seconds before
observing movement of the garage door.
6. The indicator light will (begin to) blink rapidly until programming is
complete. If your garage door opener does not operate following these
steps, repeat Steps 2 through 6. Otherwise, call the toll-free Car2U help
line at 1-866-57Car2U (1-866-572-2728).
After successful programming, you will be able to operate your Car2U
system by pressing the button you programmed to activate the opener.
The indicator light above the selected button will turn on to confirm that
the Car2U system is responding to the button command.
5


Product specificaties

Merk: Lincoln
Categorie: Auto
Model: MKZ (2010)

Heb je hulp nodig?

Als je hulp nodig hebt met Lincoln MKZ (2010) stel dan hieronder een vraag en andere gebruikers zullen je antwoorden