ZKTeco SBTL3011 Handleiding

ZKTeco Niet gecategoriseerd SBTL3011

Lees hieronder de 📖 handleiding in het Nederlandse voor ZKTeco SBTL3011 (6 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 232 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/6

Swing Barrier Instructions

Applicable Models: SBTL 2000 / 3000

Version: 1.0 Date: Nov. 2016

Chapter 2 The installation of the product

2.1 Installation notes

2.1.1 It is recommended that the swing barrier turnstile should be installed on a cement platform with

50mm to 100mm in height.

2.1.2 It is recommended that the swing barrier turnstile should not be used in corrosive environment.

2.1.3 Make sure the protective earth wire of the system is reliably connected to avoid personal injuries or

other accidents.

2.1.4 After installation, check whether connection is reliable at the connecting points of the protective

earth wire, at the connector assemblies and wiring points of the circuits, as well as at each movable part

of the swing barrier turnstile. Any loose nuts, screws and other fasteners should be tightened in time to

avoid swing barrier turnstile failures caused by long-time operations.

2.2 Installation position of the swing barrier

The installation position depends on the size of the swing barrier.If the swing barrier turnstile is installed

near a wall, a distance from100mm between the swing barrier turnstile and the wall needs to be reserved

for ease of opening the top cover of the machine to perform maintenance and adjustment. The master

and slave of a SBTL2000 swing barrier turnstile may either form a channel, or form two channels with a

SBTL2200 swing barrier turnstile,as shown in figure 2-2A;

Figure2-2A SBTL2000 Single channel and dual channel

2: left open position. (the position when the barrier is open to left)

3: right open position. (the position when the barrier is open to right)

Methods for setting the zero position of the swing boom: First press "ENT" and the menu is displayed.

Then press "UP" to move to Option 7 on the menu. Press "ENT" to make it available for value modification

and then press "UP" to set the value to 1. Turn the swing boom to the desired zero position

（，）Perpendicular to the chassis allowable deviation of 1 degrees . Finally press "ENT" and the system

gives a restart prompt. Zero calibration is finished.

Procedures for setting the left opening position of the swing boom: First press "ENT" and the menu is

displayed. Then press "UP" to move to Option 7 on the menu. Press "ENT" to make it available for value

modification and then press "UP" to set the value to 2. Move the swing boom of the gate to the desired

position on the left-hand side. Finally press "ENT" and the system will record this position as the left open

position.

Procedures for setting the right opening position of the swing boom: First press "ENT" and the menu is

displayed. Then press "UP" to move to Option 7 on the menu. Press "ENT" to make it available for value

modification and then press "UP" to set the value to 3. Move the swing boom of the gate to the desired

position on the right-hand side. Finally press "ENT" and the system will record this position as the right

opening position.

8) Language options:

0 simplified Chinese.：

1 English：

Specific operations are as follows：

Press "ENT" key to enter the menu and then press "UP/DOWN" to select the function you want.

Finally press "ENT" to confirm.

9) Opening speed : Setting the speed of opening the barrier .The speed ranges from 4 to 10.

Specific operations are as follows：

Press "ENT" key to enter the menu and then press "UP/DOWN" to select the function you want.

Finally press "ENT" to confirm.

10) Close barrier time: It is the delay after which system automatically closes the barrier after the

pedestrian passes through the channel and triggers the last infrared sensor. The unit of this delay is

second, the maximum value is 6. The default value is 0, which means that the barrier is closed

Product specificaties

Merk:	ZKTeco
Categorie:	Niet gecategoriseerd
Model:	SBTL3011
Kleur van het product:	Roestvrijstaal
Ingebouwd display:	Ja
Gewicht:	114000 g
Breedte:	260 mm
Diepte:	1500 mm
Hoogte:	1000 mm
Gewicht verpakking:	161000 g
Breedte verpakking:	760 mm
Diepte verpakking:	1640 mm
Hoogte verpakking:	1100 mm
Soort:	Neergaande arm optische tourniquet
Materiaal behuizing:	Roestvrijstaal
Frame materiaal:	Metaal
Geschikt voor buitengebruik:	Ja
Geschikt voor gebruik binnen:	Ja
AC-ingangsspanning:	110 - 220 V
Bedrijfstemperatuur (T-T):	-28 - 60 °C
Relatieve vochtigheid in bedrijf (V-V):	5 - 80 procent
Type beeldscherm:	LED
Gemiddeld aantal cycli tussen storingen (MCBF):	2000000
Barrièremateriaal:	Roestvrijstaal
Passeersnelheid (personen per minuut):	30 persoon/personen
Nooddeur ontgrendeling:	Ja