Silva Cross Trail 3 Handleiding

Silva Lamp Cross Trail 3

Lees hieronder de đź“– handleiding in het Nederlandse voor Silva Cross Trail 3 (1 pagina's) in de categorie Lamp. Deze handleiding was nuttig voor 22 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/1
Visit: www.silva.se
for more information about the
Waste Electrical and Electronic
Equipment (WEEE) Directive.
Thank you for choosing Silva Cross Trail 3 headlamp. This headlamp can, thanks to the
modular design, also be used on a helmet or on a bike handle bar.
Cross Trail 3 and 3X are our first lamps featuring Flow light
® - a technology that lets you
control the light beam by tilting the lamp vertically and varies the light pattern infinitely
depending on where you aim the light. Thus the lamp is adaptable for slow or fast activities.
PRODUCT OVERVIEW
The Cross Trail 3 headlamp packaging consists of the following parts:
• Headlamp body
• Headband
• Helmet bracket with adhesive strip
• Bike bracket
• Extension cable with helmet strap
• Cable holder
• Battery box with Velcro strap
• 4 pcs AA batteries
• Quick guide
BEFORE USE
ADJUST THE HEADBAND
The elastic headband is designed to give a comfortable fit at speed during activities such as
running, XC skiing etc. Adjust the headband by moving the sliding buckle to fit it onto your
head.
INSERT THE BATTERIES
Open the battery case and insert the four AA batteries. Either Alkaline (Included), Nimh or
Lithium batteries can be used. Please note the battery polarity. Do not mix different brands
of batteries. Do not mix batteries with different levels of discharge.
If you don’t intend to use the headlamp for several months, make sure you remove the bat-
teries from the lamp.
FLEXIBLE BATTERY CARRYING
The battery pack can be carried in multiple ways; for example on the head band, in a
pocket, backpack, on the waist or mounted on the bike frame by using the soft case with the
integrated strap.
MODULAR SYSTEM
In order to move the headlamp body from the headband to either the helmet bracket or the
bike bracket, gently push the lamp upward relative the head plate with head band. Insert
the headlamp body in the new bracket and gently press it down until you hear a click sound.
MOUNTING THE HELMET BRACKET
The helmet bracket comes with pre mounted adhesive on the back for easy mounting on any
helmet. The adhesive is a polyethylene foam tape developed to not damage or cause any
type of weakness to the plastic in your helmet.
Before mounting the helmet bracket on a helmet, make sure the surface is dry and clean.
Remove the protective paper from the adhesive tape on the helmet bracket. Gently press
the helmet bracket to the helmet.
Depending on helmet type, it might be preferable to use the 4th light mode (Helmet mode – Flow
light deactivated), when the Cross Trail 3 is used on a helmet.
With Flow light deactivated you can tilt the lamp in a preferable position without affecting the light
beam.
MOUNTING THE BIKE BRACKET
The bike handlebar bracket is developed for use on bike handlebars with a dimension
between 25 and 32 mm.
DURING USE
FLOW LIGHT®
The Cross Trail 3 headlamp is equipped with Flow Light
® which is a light distribution technology
that combines a wide angle flood light with a long reach spot light. If you aim the light beam of
the Cross trail 3 close to your feet by rotating the lamp body downward, the light beam will be
a wide flood light adapted for slower activities. If you aim the light higher up, further away, the
light beam will gradually transform into a long distance spot beam, perfect for higher speed.
This unique feature gives the user peripheral or long distance vision depending on the activity or
speed. For a runner, cross country skier, mountain biker or night orienteer this translates into
less head movement, increased control, better balance and more speed.
SWITCH ON YOUR HEADLAMP
On the side of the headlamp body there is a push button which controls all light modes.
Each press on the button gives you the following light:
1. Turns the headlamp ON with all LEDs in maximum power
2. Med mode
3. Min mode
4. Max mode with Flow light deactivated (helmet mode)
5. Blink
6. Starts over from 1 – Max mode
To turn OFF the headlamp; press and hold the button for 2 seconds.
TEMP CONTROL
The headlamp temperature will increase during use. The headlamp temperature is mainly
depending on light mode, ambient temperature and the airflow (speed). The Cross Trail 3
headlamp is equipped with a temperature control function which prevents the headlamp
body from overheating by reducing the power to the LEDs. This means that the lower the
ambient temperature, the stronger the light output.
Note: Always make sure that the batteries are disconnected when the headlamp is stored in
a closed compartment such as a bag, pocket or similar.
BATTERY INDICATION
When the headlamp is turned off a small LED is turned on inside the front of the headlamp
to indicate the status of the batteries. The battery status indication LED will be on for 5
seconds after power off.
Green light – Battery in good condition (more than ~70% remaining)
Red – Battery in poor condition (less than ~30% remaining)
LOW BATTERY WARNING
During operation of the headlamp there will be a low battery warning when 25-30% of the
battery energy remains. This is done by flashing both LEDs for 1 second and repeated again
after 5 seconds.
AFTER USE
MAINTENANCE
To make sure you get maxim um performance from your Cross Trail 3 headlamp, clean it
regularly with a damp cloth.
Headset cleaning – wash in washing machine at 40 ºC.
TECHNICAL SPECIFICATIONS
Weight: headlamp (excluding battery): 70g
Weight: battery 150g
Battery type: Alkaline (included), Nimh or Li (Nominal battery voltage 1.2-1.5V)
Light distance (Max/Med/Min): 120m/70m/50m
Lumen (Max, Med, Min): 400, 200, 100 Lumen
Burn time: (Max/Med/Min): 6h/12h/24h
Water resistance: IPX6
Material head lamp body: PC/ABS and Aluminium
Operative temperature range: -10Âş - +55 ÂşC
Storage temperature range: -20 - +35 ÂşC
Art No: 37535
PROTECT THE ENVIRONMENT.
Headlamp and batteries should be recycled and must not be thrown in the regular trash.
Dispose these items in accordance with applicable local regulations.
WARRANTY
Silva warrants that, for a period of two (2) years, your Silva Product will be substantially
free of defects in materials and workmanship under normal use. Silva’s liability under this
warranty is limited to repairing or replacing the product. This limited warranty extends only
to the original purchaser.
If the Product proves defective during the Warranty Period please contact the original place
of purchase. Make sure to have your proof of purchase on hand when returning the product.
Returns cannot be processed without the original proof of purchase. This warranty does not
apply if the Product has been altered, not been installed, operated, repaired, or maintained
in accordance with instructions supplied by Silva, or has been subjected to abnormal physi-
cal or electrical stress, misuse, negligence or accident. Neither does the warranty cover
normal wear and tear. Silva is not responsible for any consequences, direct or indirect,
or damage resultant from use of this product. In no event will Silva’s liability exceed the
amount paid by you for the product. Some jurisdictions do not allow the exclusion or limita-
tion of incidental or consequential damages, so the above limitation or exclusion may not
apply to you. This Warranty is valid and may be processed only in the country of purchase.
For more information please visit www.silva.se
FULL VERSION MANUAL
CROSS TRAIL 3 Art. No 37535


Product specificaties

Merk: Silva
Categorie: Lamp
Model: Cross Trail 3

Heb je hulp nodig?

Als je hulp nodig hebt met Silva Cross Trail 3 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Lamp Silva

Handleiding Lamp

Nieuwste handleidingen voor Lamp