Rossmax ThermoCal - Professional Testing Device for Thermometer Handleiding

Rossmax Thermometer ThermoCal - Professional Testing Device for Thermometer

Lees hieronder de 📖 handleiding in het Nederlandse voor Rossmax ThermoCal - Professional Testing Device for Thermometer (2 pagina's) in de categorie Thermometer. Deze handleiding was nuttig voor 27 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

Instruction Manual

Model: ThermoCal

Professional Testing Device

for Thermometer

www.rossmax.com

OBM_IB_ThermoCal_ver1411

Manufacturer: Rossmax Swiss GmbH,

Tramstrasse 16, CH-9442 Berneck, Switzerland

2. Heating indicator of the water bath does not light up after the calibration temperature is set

Possible causes Actions to take

Water temperature is higher than the set

temperature Cool down the water in the bath

Defective heating indicator Contact Rossmax for service

Defective temperature controller Contact Rossmax for service

Set temperature is too low Set temperature should be at least 5°C higher

than operating temperature

3. Heating indicator of water bath lights up, whereas the water temperature remains low

Possible causes Actions to take

Defective heater circuit Contact Rossmax for service

Defective temperature controller Contact Rossmax for service

4. Water temperature continues to rise and exceed the set temperature

Possible causes Actions to take

Defective temperature controller Contact Rossmax for service

5. Large uctuation in water temperature

Possible causes Actions to take

Water temperature is not stable yet Wait for temperature to stabilize

Set temperature is too close to ambient

temperature Lower the ambient temperature

Defective temperature controller Contact Rossmax for service

Defective water heater Contact Rossmax for service

6. Power and power indicator are both on, whereas the water circulating pump does not start

Possible causes Actions to take

Foreign object clogs inside the pump Remove the foreign object

Loose screw used to secure the propeller Tighten the screw

Defective motor Contact Rossmax for service

7. Noise generated by the stirrer motor

Possible causes Actions to take

Bearing ball oxidation Replace bearing

Bearing aging Replace bearing

Trouble shooting

1. Power is switched on but the power indicator does not light up

Possible causes Actions to take

No power input Check the power source

Loose plug Insert the plug into the socket securely

Device is powered and running but the power

indicator does not light up Replace the power switch

Power wire broke or loose connection Replace the power wire(s)

Tripped fuse Check the fuse and replace it if needed

WARNING: The symbol on this product means that it’s an

electronic product and following the European directive

2012/19/EU the electronic products have to be disposed

on your local recycling centre for safe treatment.

Accuracy is always the biggest concern of a thermometer user. Rossmax ThermoCal is a portable

and convenient device that allows the user to easily check the accuracy of a thermometer in just a

few seconds. The innovative design of the adjustable blackbody cavity applies to all three types of

Rossmax thermometer products - pen type, ear and forehead thermometer.

Parts name/location

Control panel Back view

Introduction

Instructions for installation

Cautions and maintenance

Specications

Operation procedures

1. Check the accuracy

Step 1: Check water level of the bath.

Step 2: Turn on the device.

Step 3: Select a testing temperature on the control panel (default at 37°C).

Step 4: Wait for the water to reach the desired temperature.

Step 5: Choose the blackbody cavity corresponding to the thermometer types.

Step 6: Set the thermometer into the calibration mode.

Step 7: Insert the probe/tip into the cavity.

Step 8: Start the measurement.

Step 9: Thermometer will beep when the measurement is completed.

Step 10: Compare the reading given by the thermometer to the calibration temperature.

The acceptable allowance is within ±0.2°C.

2. Drain the water bath

Step 1: Make sure the device is off.

Step 2: Remove the tube from the upper end.

Step 3: Empty the water bath by lowering the upper end of the tube.

Step 4: Plug the tube back in after the draining is completed.

1. Install the device on a solid surface.

2. Make sure the power is off before plugging in the device.

3. Keep the device away from the environment with direct sunlight, high temperature, high

humidity or severe change in temperature.

4. Make sure the AC power and its grounding plug are properly connected.

5. Do not use power extension cords.

6. Use pure water or distilled water only for the water bath to avoid contamination or water

heater breakdown.

7. Pay attention to the water level to avoid overspill.

8. The water bath is to remain 90% full at all times to reach water temperature stability.

1. Make sure the device, AC power and its grounding plug, is plugged in properly.

2. Change water periodically, once a month is suggested.

3. Use pure water or distilled water only for the water bath. Other water sources might increase

the chance of calcium carbonate formation on the outside of the water heater.

4. Make sure there is enough water in the water bath every time before using the device. Please

constantly pay attention to the water level and hygiene when/if the device runs for over 6 hours

or the water temperature exceeds 40°C.

5. Keep the device away from physical impact.

6. Unplug the device and empty the water bath if the device is going to be inactive for a long

time.

7. Unplug the device before moving it or draining the water bath.

8. Clean the water bath with a 3M scrub sponge if any signs of iron oxidization appear.

9. Pay attention to the water temperature to avoid scald.

Power source AC 100-240V 50/60 Hz

Power of water heater 255W

Testing temperature Ambient temperature + 5°C to maximum 45°C

Ambient temperature 16 ~ 30°C

Stability of water bath temperature ± 0.02°C

Diameter of

blackbody cavity

Pen type 15 mm

Ear 12.5 mm

Forehead 55 mm

Capacity 5.39 Liters

Weight 9.69 kgs

Dimension 180(W) x 350(H) x 320(D) mm

Control

panel

Ventilation

holes

Water

bath actual

temperature

Water bath set

temperature

Heating

indicator

Temperature up

Temperature down

Digit selecting key

Temperature setting key

Socket

and fuse

Power

switch

Cooling

fan

Overheating

protection

setting knob

Drain

tube

Removable

bath cover Blackbody

cavity

Computer

Product specificaties

Merk:	Rossmax
Categorie:	Thermometer
Model:	ThermoCal - Professional Testing Device for Thermometer

Heb je hulp nodig?

Als je hulp nodig hebt met Rossmax ThermoCal - Professional Testing Device for Thermometer stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag