RCBS Competition Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor RCBS Competition (8 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 48 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/8
COMPETITION
POWDER MEASURE
WARNING:
NOT FOR USE WITH
BLACK POWDER!
PRODUCT INSTRUCTIONS
SAFETY
Reloading is an enjoyable and rewarding hobby that is easily conducted with
safety. But carelessness or negligence can make reloading hazardous. This product has
been designed from the beginning with the user’s safety in mind.
As with any reloading operation, some safety rules must be followed. By
observing these few rules, the chance of hazardous occurrence causing damage or injury
becomes extremely remote.
GENERAL
Use the equipment as the manufacturer recommends. Study the instructions
carefully and become thoroughly familiar with the operation of the product. Don’t
take short cuts.
Observe “good housekeeping” in the work area. Keep tools and components neat,
clean and orderly. Promptly clean up any powder spills.
Always wear adequate eye protection.
If any unusual resistance is encountered when moving the operating handle, STOP
IMMEDIATELY and investigate the cause. To proceed against unusual resistance
may damage equipment and/or cause serious injury!
LOADING DATA
Use only laboratory tested data. We highly recommend the use of the SPEER
Reloading Manual.
OBSERVE ALL WARNINGS ABOUT THE USE OF MAXIMUM LISTED
LOADS.
POWDER HANDLING
Store primers and powder beyond the reach of children and away from heat,
dampness, open ames and electrical equipment.
DO NOT use any powder unless its identity is positively known. Discard all mixed
powders and those of uncertain or unknown identity.
Before charging cases, settle the powder in the powder hopper. Throw and check the
weight of at least ten charges. This will assure you that the correct powder charge is
being thrown.
Use of a powder bae will help to throw consistent charges.
After a reloading session ends, pour the remaining powder back in its original
factory container. This will preserve the identity and shelf life of the powder.
DO NOT smoke while handling powder or primers.
DO NOT USE BLACK POWDER with the Competition Powder Measure.
RECORD KEEPING
Keep complete records of reloads. Apply a descriptive label to each box showing the
date produced, and the primer, powder and bullet used. Labels for this purpose are
packed with SPEER bullets.
Since RCBS has no control over the choice of components, the manner in which they
are assembled, the use of this product, or the rearms in which the resulting
ammunition may be used, no responsibility, either expressed or implied, is assumed
for the use of ammunition reloaded with this tool.
NOT FOR USE WITH BLACK POWDER
GENERAL INFORMATION
The Uniow Powder Measure will perform two powder charging tasks in one
fast, simple operation. With each turn of the handle it accurately measures powder
within a fraction of a grain and swiftly dispenses it into cases, one after another.
Powder pours uniformly from the powder hopper into the measuring cylinder,
through the drop tube and into the case. This eliminates the hazards of overloads
caused by clogging when charges are dumped into cases. You can change from one
charge to another quickly and easily with the Micrometer measuring screw which
also serves as a reference for future charges.
The powder level is visible at all times through a large capacity ve inch plastic
powder hopper.
The measuring cylinder has a precision-ground surface and slides into the honed
main casting for a precise t. The lower portion of the main casting has the standard
7/8- threads and may be used with the furnished stand plate or an optional 14
Powder Measure/Piggyback Stand.
A powder measure is basically a device which measures powder by volume and
not by weight. However, before you start throwing a given charge with this powder
measure, the rst charge must always be weighted on a powder scale to arrive at the
desired charge. Accurate powder measure charges will also depend upon the size
and uniformity of the powder kernels used, and how smoothly and uniformly you
operate the powder measure handl e.
Ball and ake powders will measure very evenly. Long and short kernel stick-
type powders e more dicult to measure consistently, and it is imperative that you ar
follow a set routine when throwing charges of these powders.
TO ASSEMBLE
To prepare the Uniow Powder Measure for use, the measuring cylinder,
Micrometer measuring screw, inside of main casting and powder funnel portion of
main casting must be cleaned to remove the factory applied rust preventative.
Failure to do so will cause inconsistent powder charges.
Insert screws through the handle and attach to the measuring cylinder with
handle facing toward the unthreaded portion of the measuring cylinder. Carefully
insert the assembly into the Uniow main casting, this is a precise t, do not force
the cylinder into the casting. The Powder Measure can be set up for right or left
handed use depending on which way you slide in the assembly.


Product specificaties

Merk: RCBS
Categorie: Niet gecategoriseerd
Model: Competition

Heb je hulp nodig?

Als je hulp nodig hebt met RCBS Competition stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd RCBS

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd