Intel Edison Breakout Board Handleiding

Intel Niet gecategoriseerd Edison Breakout Board

Lees hieronder de 📖 handleiding in het Nederlandse voor Intel Edison Breakout Board (32 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 216 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/32
Intel® Edison Kit for Arduino*
Hardware Guide
December 2014
Revision 004
- Document Number: 331191 004
Notice: This document contains information on products in the design phase of development. The information here is subject to change without
notice. Do not finalize a design with this information.
INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION WITH INTEL PRODUCTS. NO LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR
OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. EXCEPT AS PROVI DED IN INTEL’S TERMS AND
CONDITIONS OF SALE FOR SUCH PRODUCTS, INTEL ASSUMES NO LIABILITY WHATSOEVER AND INTEL DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY, RELATING TO SALE AND/OR USE OF INTEL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A
PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
A "Mission Critical Application" is any application in which failure of the Intel Product could result, directly or indirectly, in personal injury or death.
SHOULD YOU PURCHASE OR USE INTEL’S PRODUCTS FOR ANY SUCH MISSION CRITICAL APPLICATION, YOU SHALL INDEMNIFY AND HOLD INTEL
AND ITS SUBSIDIARIES, SUBCONTRACTORS AND AFFILIATES, AND THE DIRECTORS, OFFICERS, AND EMPLOYEES OF EACH, HARMLESS AGAINST
ALL CLAIMS COSTS, DAMAGES, AND EXPENSES AND REASONABLE ATTORNEYS' FEES ARISING OUT OF, DIRECTLY OR INDIRECTLY, ANY CLAIM OF
PRODUCT LIABILITY, PERSONAL INJURY, OR DEATH ARISING IN ANY WAY OUT OF SUCH MISSION CRITICAL APPLICATION, WHETHER OR NOT
INTEL OR ITS SUBCONTRACTOR WAS NEGLIGENT IN THE DESIGN, MANUFACTURE, OR WARNING OF THE INTEL PRODUCT OR ANY OF ITS PARTS.
Intel may make changes to specifications and product descriptions at any time, without notice. Designers must not rely on the absence or
characteristics of any features or instructions marked “reserved” or “undefined.” Intel reserves these for future definition and shall have no
responsibility whatsoever for conflicts or incompatibilities arising from future changes to them. The information here is subject to change without
notice. Do not finalize a design with this information.
Intel software products are copyrighted by and shall remain the property of Intel Corporation. Use, duplication, or disclosure is subject to
restrictions stated s Software License Agreement, or in the case of software delivered to the government, in accordance with the software in Intel’
license agreement as defined in FAR 52.227- 7013.
The products described in this document may contain design defects or errors known as errata which may cause the product to deviate from
published specifications. Current characterized errata are available on request.
The code names presented in this document are only for use by Intel to identify products, technologies, or services in development that have not
been made commercially available to the public, i.e., announced, launched, or shipped. They are not "commercial" names for products or services
and are not intended to function as trademarks.
Contact your local Intel sales office or your distributor to obtain the latest specifications and before placing your product order.
Copies of documents which have an order number and are referenced in this document, or other Intel literature may be obtained by calling
1- - - . 800 548 4725 or by visiting Intel’s website at http://www.intel.com/design/literature.htm
Intel processor numbers are not a measure of performance. Processor numbers differentiate features within each processor family, not across
different processor families. See for details. http://www.intel.com/products/processor_number
Intel, the Intel logo, and Intel Atom are trademarks of Intel Corporation in the United States and other countries .
* Other brands and names may be claimed as the property of others.
Copyright © 2014 Intel Corporation. All rights reserved.
Intel® Edison Kit for Arduino*
Hardware Guide December 2014
2 1- Document Number: 33119 004
Contents
1 Introduction ....................................................................................................................................................................... 6
1.1 Software requirements ............................................................................................................................................................... 6
1.2 Terminology .................................................................................................................................................................................... 6
1.3 References ........................................................................................................................................................................................ 6
2 Product Overview ............................................................................................................................................................. 7
2.1 Shield pin GPIO mapping .......................................................................................................................................................... 8
2.2 Pin function multiplexing control (summary) .................................................................................................................. 9
2.3 Pin function multiplexing control (detailed) .................................................................................................................. 10
2.4 GPIO interrupt support ............................................................................................................................................................ 11
2.5 Miscellaneous GPIOs............................................................................................................................................................... 11
2.6 Pin direction and pullup control ......................................................................................................................................... 12
3 - High Level Functional Description ............................................................................................................................. 13
3.1 Intel® Edison kit for Arduino* header signal list ........................................................................................................... 14
3.2 Intel® Edison kit for Arduino* PWM swizzler ................................................................................................................. 15
3.3 Intel® Edison kit for Arduino* analog inputs .................................................................................................................. 16
3.4 Intel® Edison kit for Arduino* signal pullup resistors ................................................................................................ 16
3.5 Intel® Edison kit for Arduino* USB interface .................................................................................................................. 16
3.6 Intel® Edison kit for Arduino* power supply .................................................................................................................. 17
3.7 Intel® Edison kit for Arduino* expansion mechanicals ............................................................................................. 17
4 Powering the Intel® Edison kit for Arduino*................................................................................................................18
4.1 Boot voltage selection – DCIN signal ................................................................................................................................ 19
5 Batteries............................................................................................................................................................................ 20
6 Layout................................................................................................................................................................................ 21
6.1 Antenna keepout ........................................................................................................................................................................ 21
6.2 Layout SD card, I2S, SPI, I2C ................................................................................................................................................. 21
6.3 LEDs .................................................................................................................................................................................................. 22
7 Handling ...........................................................................................................................................................................23
8 Debug UART and Low- Power Sleep Mode ................................................................................................................ 24
9 Buttons.............................................................................................................................................................................. 25
9.1 Software recovery (FWR_RCVR and RCVR_MODE) .................................................................................................... 25
10 Digikey sources ............................................................................................................................................................... 26
11 Shield pin configuration............................................................................................................................................... 27
11.1 Configure IO5 as a GPIO input, with pullup resistor disabled ............................................................................... 27
11.2 Configure IO11 as a GPIO input, with pullup resistor disabled .................................................................................. 28
11.3 Configure IO7 a as GPIO input, with pullup resistor enabled ........................................................................... 28
11.4 Configure IO6 a as PWM output........................................................................................................................................ 29
11.5 Configure IO14 as an ADC input ....................................................................................................................................... 29
11.6 IO18/IO19 Configure Ifor 2C connectivity..................................................................................................................... 30
11.7 Configure connectivity IO10 through IO13 for SPI ..................................................................................................31
Intel® Edison Kit for Arduino*
December 2014 Hardware Guide
Document Number: 331191- 3 004
Figures
Figure 1 Arduino* Uno* pinout............................................................................................................................................................. 7
Figure 2 Intel® Edison kit for Arduino* block diagram ............................................................................................................ 13
Figure 3 Intel® Edison kit for Arduino* PWM swizzler ............................................................................................................15
Figure 4 PWM swizzler on the Intel® Edison kit for Arduino*.............................................................................................. 16
Figure 5 Intel® Edison kit for Arduino* mechanical dimensions ........................................................................................ 17
Figure 6 Intel® Edison kit for Arduino* power distribution network ................................................................................ 18
Figure 7 Area around antenna ........................................................................................................................................................... 21
Figure 8 Inserting an Intel® Edison compute module ............................................................................................................. 23
Figure 9 Digikey sources....................................................................................................................................................................... 26
Tables
Table 1 - Product specific documents ............................................................................................................................................... 6
Table 2
Shield pin GPIO mapping
................................................................................................................................................... 8
Table 3 Arduino* pin mux and pin mode settings ..................................................................................................................... 9
Table 4 Pin function multiplexing control .................................................................................................................................. 10
Table 5 GPIO interrupt support....................................................................................................................................................... 11
Table 6
Miscellaneous GPIOs
......................................................................................................................................................... 11
Table 7
Pin direction and pullup control
................................................................................................................................. 12
Table 8 Intel® Edison kit for Arduino* header signal list ...................................................................................................... 14
Table 9 Intel® Edison kit for Arduino* PWM swizzler signal assignments ................................................................... 15
Table 10 Layout SD card........................................................................................................................................................................ 21
Intel® Edison Kit for Arduino*
Hardware Guide December 2014
4 1- Document Number: 33119 004
Revision History
Revision Description Date
ww32
Initial release
August 4, 2014
ww34
Minor edits.
August 20, 2014
ww36
Removed a column from Table 2.
September 5, 2014
001
First public release.
September 9, 2014
002
Minor corrections. September 15, 2014
003
Added product over chapter and shield pin configuration chapter. view September 18, 2014
004
Updated control and LEDssections on recovery mode in function musoftware , p x s, . December 1, 2014
§
Intel® Edison Kit for Arduino*
December 2014 Hardware Guide
Document Number: 331191- 5 004
Shield pin configuration
1 Introduction
This document describes the hardware interface of the Intel® Edison kit for Arduino*.
The kit contains external input/output pin connections which may be configured to be used in a variety of
interfacing modes, such as GPIO, PWM, SPI, I2C, ADC, for compatibility with Arduino* Uno* shield hardware. This
document describes the pin functions available, detailed GPIO pin mapping for pin control and I/O, and use of
Linux command line tools to configure the external I/O pin functions correctly for the desired mode of operation.
1.1 Software requirements
• Intel® Edison kernel and BSP.
• Access to the Linux command line on an Intel® Edison compute module.
1.2 Terminology
Term Definition
PWM
Pulse width modulation
GPIO
General purpose input/output
ADC
Analog to digital converter
SPI
Serial peripheral interface
I
2
C
Inter- integrated circuit
1.3 References
Table 1 - Product specific documents
Reference Name Number/location
331188
Intel® Edison Board Support Package User Guide
331189
Intel® Edison Compute Module Hardware Guide
331190
Intel® Edison Breakout Board Hardware Guide
331191
Intel® Edison Kit for Arduino* Hardware Guide (This document)
329686
Intel® Galileo and Intel® Edison Release Notes
[GSG] Intel® Edison Getting Started Guide
M: https://communities.intel.com/docs/DOC-23148
L: https://communities.intel.com/docs/DOC-23149
331438
Intel® Edison Wi Fi Guide-
§
Intel® Edison Kit for Arduino*
Hardware Guide December 2014
6 1- Document Number: 33119 004
Shield pin configuration
2 Product Overview
The 20 Arduino* are numbered IO0- compatible shield I/O pins on the Intel® Edison kit for Arduino* - 1IO19 (Figure ).
All pins support basic GPIO functionality. Some of the pins also support PWM, ADC, SPI or I
2C functions. Selection
of different pin functions on the Intel® Edison kit for Arduino* is achieved through use of SoC pin control interfaces
and GPIO output signals dedicated for multiplexing control. The following sections detail the mapping of each of
the GPIO pins available on the Intel® Edison to their respective functions, which can be broadly compute module
categorized as follows (see Figure 1 ):
• External GPIO. Used for digital input/output signaling via the external shield pins.
• Pin multiplexing control. Used for selecting different functions available on a given shield pin.
• Pin buffer (level-shifter) direction control. Used to configure the buffer on a given shield pin for input or
output.
• Pin pullup resistor control. Used to enable/disable a pullup resistor on a given shield pin.
To use any of the supported functions on a shield pin, it is first necessary to configure the multiplexing, buffer
direction, and pullup resistor controls applicable to that pin.
Figure 1 Arduino* Uno* pinout
Intel® Edison Kit for Arduino*
December 2014 Hardware Guide
Document Number: 331191- 7 004
Shield pin configuration
2.1 Shield pin GPIO mapping
Table 2 describes the mapping of GPIO and PWM pin numbers (in Linux) to shield I/O pins. The following details
are included:
• Shield pin. Digital I/O pin number as per Arduino* Uno* pin numbering scheme.
• GPIO (Linux). The pin number assigned under Linux.
• Muxed functions. Other signals available on this shield pin, as they appear on the schematic.
Table 2
Shield pin GPIO mapping
Shield pin GPIO (Linux) PWM (Linux) Muxed functions Notes
IO0
130
UART1_RXD
IO1
131
UART1_TXD
IO2
128 UART1_CTS Note 1.
IO3 12 0 PWM0 Note 2.
IO4
129
UART1_RTS
Note 1.
IO5
13
1
PWM1
Note 2.
IO6
182
2
PWM2
Note 2.
IO7
48
─
IO8
49
─
─
─
──
IO9
183 3 PWM3 Note 2.
IO10
41
??
SPI_2_SS1
I2S_2_FS
Note 1.
PWM4_OUT
Note 2.
IO11 43 ?? SPI_2_TXD
I2S_2_TXD Note 1.
PWM5_OUT Note 2.
IO12
42
SPI_2_RXD
I2S_2_RXD
Note 1.
IO13
40
SPI_2_CLK
I2S_2_CLK Note 1.
IO14 44 AIN0
IO15
45
AIN1
IO16
46
AIN2
IO17
47
AIN3
IO18 14 AIN4
I2C_6_SDA
IO19 165 AIN5
I2C_6_SCL
1 Some additional functions are available on certain SoC pins, such as I2S and UART flow control, but they are not currently
supported by the Arduino library. However, it may be possible to use these from Linux.
2 Depends on PWM swizzler. The SoC offers only four PWM pins. A jumper pin matrix labeled “PWM swizzler” on the baseboard
allows these pins to be connected to any subset of the four six -shield header pins normally used for PWM. From the factory,
IO3, IO5, IO6, and IO9 will be connected to the four available SoC PWM pins as described above. You can manually alter
these to connect IO10 or IO11.
Intel® Edison Kit for Arduino*
Hardware Guide December 2014
8 1- Document Number: 33119 004
Shield pin configuration
2.2 P in function multiplexing control (summary)
All GPIO pins on the Arduino* rheader require some inte nal GPIOs to be set up before the pin is usable. This is
usually as simple as setting an output enable, pullup enable, and mode. However, some pins have extra
functionality such as SPI, PWM, or I2C, so these pins need extra multiplexing (muxing) in order to be usable.
Table 3 shows this such that a programmer can easily see all the muxing pins affected for a given Arduino* header
pin. The color codes in the table show related boxes. For example, the blue boxes are meant to show the
relationship between the pin mux pins and the pin modes. This table is a synopsis of the more detailed tables
below, which contain extra information, such as schematic pin numbers. For most needs, this synopsized table
should suffice.
T 3 able Arduino* pin mux and pin mode settings
Linux
GPIO
pin
GPIO pin mux SoC pin modes Output enable
(high = output)
Pullup
enable
Linux pin 0 1 0 (low) 1 (high) Linux Linux
IO0
130
GPIO
UART
248
216
IO0
130
GPIO
UART
248
216
IO1
131 249 217 GPIO UART
IO2
128 250 218 GPIO UART
IO3
12 251 219 GPIO PWM
IO4
129
GPIO
UART
252
220
IO5
13
GPIO
PWM
253
221
IO6
182 254 222 GPIO PWM
IO7
48 255 223 GPIO
IO8
49 256 224 GPIO
IO9
183
GPIO
PWM
257
225
IO10
41
263
PWM
see 240
GPIO
I2S or SPI
258
226
240
GPIO or I2S
GPIO or SPI_FS
IO11
43 262 259 227 PWM see 241 GPIO I2S or SPI
241 GPIO or I2S GPIO or SPI TXD
IO12
42 242 260 228 GPIO or I2S GPIO or SPI RXD GPIO I2S or SPI
IO13
40
243
GPIO or I2S
GPIO or SPI CLK
GPIO
I2S or SPI
261
229
IO14 (A0)
44
200
GPIO
A0
GPIO
232
208
IO15 (A1)
45
201
GPIO
A1
GPIO
233
209
IO16 (A2)
46 202 234 210 GPIO A2 GPIO
IO17 (A3) 47 203 235 211 GPIO A3 GPIO
IO18 (A4)
14
204
GPIO or I2C SDA
A4
GPIO
I2C-6
236
212
IO19 (A5)
165
205
GPIO or I2C SCL
A5
GPIO
I2C-6
237
213
Note: Before setting up any muxing, pin 214 (TRI_STATE_ALL) set to of LOW, make all your changes, then set pin
214 to HIGH.
Intel® Edison Kit for Arduino*
December 2014 Hardware Guide
Document Number: 331191- 9 004
Shield pin configuration
2.3 Pin function multiplexing control (detailed)
Table 4 lists the GPIO outputs dedicated to pin multiplexing control. Different functions may be selected for
specific shield I/O pins by setting these GPIO outputs to 0/1 (low/high). Additionally, some of the SoC GPIO pins
also feature internal mux options. These are listed as “SoC Pin Modes”.
Currently, these are configured by setting the required pin mode for the corresponding SoC GPIO pin N, via
/sys/kernel/debug/gpio_debug/gpioN/current_pinmux, to “mode[0/1/2/...]”
Table 4 Pin function multiplexing control
Shiel
d pin
GPIO pin mux SoC pin modes
Pin Pin Linux 0 (low) 1 (high) Power- on default 0 1 2 Linux
IO0
-
GP130
130
GPIO
UART
IO1
-
GP131
131
GPIO
UART
IO2
-
GP128
128
GPIO
UART
IO3
-
GP12
12
GPIO
PWM
IO4
- GP129 129 GPIO UART
IO5
- GP13 13 GPIO PWM
IO6
- GP182 182 GPIO PWM
IO7
-
GP48
48
GPIO
IO8
-
GP49
49
GPIO
IO9
-
GP183
183
GPIO
PWM
IO10 U34_ IO1.7 263 PWM4_OUT
GP41
Pulled down input GP41 41 GPIO I2S
SSP5_FS_1
U16_ IO1.0
240
GP41
SSP5_FS_1
Pulled up input 1
GP111
111
GPIO
SPI
IO11
U34_ IO1.6
262
PWM5_OUT
GP43
Pulled down input
GP43
43
GPIO
I2S
SSP5_TXD
GP115
115
GPIO
SPI
U16_ IO1.1
241
GP43
SSP5_TXD
Pulled up input
1
IO12
U16_ IO1.2
242
GP42
SSP5_RXD
Pulled up input
1
GP42
42
GPIO
I2S
GP114
114
GPIO
SPI
IO13
U16_ IO1.3
243
GP40
SSP5_CLK
Pulled up input
1
GP40
40
GPIO
I2S
GP109
109
GPIO
SPI
IO14
U17_ IO0.0
200
GP44
A0
Pulled up input
1
GP44
44
GPIO
IO15
U17_ IO0.1
201
GP45
A1
Pulled up input
1
GP45
45
GPIO
IO16
U17_ IO0.2
202
GP46
A2
Pulled up input
1
GP46
46
GPIO
IO17
U17_ IO0.3
203
GP47
A3
Pulled up input
1
GP47
47
GPIO
IO18
U17_ IO0.4
204
GP14
A4
Pulled up input
1
GP14
14
GPIO
I2C-6
I2C-8
I2C6_SCL
GP28
28
GPIO
IO19
U17_ IO0.5
205
GP165
A5
Pulled up input
1
GP165
165
GPIO
I2C-6
I2C-8
I2C6_SDA
GP27
27
GPIO
1. pThese pins are ulled up inputs at power- m on. This effectively enables the ux switches (i.e. x function 1 is selected).mu
Intel® Edison Kit for Arduino*
Hardware Guide December 2014
10 33119 Document Number: 1- 004
Shield pin configuration
2.4 GPIO interrupt support
All GPIO inputs on the Intel® Edison platform are interrupt- capable, and all interrupt types are supported on all
inputs. Table 5 - lists the specific edge and level- triggered interrupt types that are supported on each pin.
Table 5 GPIO interrupt support
Shield pin - -GPIO Edge triggered Level triggered 1
Linux
Rising
Falling
Both
Low High
IO0
130
Y
Y
Y
Y
Y
IO1
131 Y Y Y Y Y
IO2
128 Y Y Y Y Y
IO3
12
Y
Y
Y
Y
Y
IO4
129
Y
Y
Y
Y
Y
IO5
13
Y
Y
Y
Y
Y
IO6
182 Y Y Y Y Y
IO7 48 Y Y Y Y Y
IO8
49 Y Y Y Y Y
IO9
183
Y
Y
Y
Y
Y
IO10
41
Y
Y
Y
Y
Y
IO11
43 Y Y Y Y Y
IO12
42 Y Y Y Y Y
IO13 40 Y Y Y Y Y
IO14
44
Y
Y
Y
Y
Y
IO15
45
Y
Y
Y
Y
Y
IO16
46
Y
Y
Y
Y
Y
IO17
47 Y Y Y Y Y
IO18 14 Y Y Y Y Y
IO19
165 Y Y Y Y Y
1. - Level triggered interrupts are not supported by the Arduino* library, a limitation of the GPIO sysfs interface.
2.5 Miscellaneous GPIOs
The GPIOs listed in Table 6 are used for other platform functions and for Arduino shield compatibility.
Table 6
Miscellaneous GPIOs
Function GPIO pin GPIO Linux on default -Direction Power 1 Initial setup
TRI_STATE_ALL
U17_IO1.6
214
Output
Pulled up input*
SHLD_RESET
U17_IO1.7
215
Output
Pulled up input*
SHLD_RESET
U17_IO0.7 207 Input Pulled up input*
1 These pins are pulled up inputs at power- on. In this state, they have the same effect as outputs set high.
Intel® Edison Kit for Arduino*
December 2014 Hardware Guide
Document Number: 331191- 004 11
Shield pin configuration
2.6 Pin direction and pullup control
For most shield pins on the Intel® Edison kit for Arduino*, there is a buffer/level-shifter which needs to be
configured for input or output direction, and an external 47 kohm pullup/pulldown resistor, which may be
optionally enabled. Both are driven by dedicated GPIO outputs, listed . When configuring a shield pin as in Table 7
an output, we advise configuring the buffer for output before setting the SoC GPIO pin direction to output. To
disconnect the external pullup/pulldown resistors, it is necessary to configure as high-impedance inputs the GPIOs
that drive them.
Note also that the GPIO signals from the PCAL9555A GPIO expanders have internal 100 kohm pullup resistors,
which are connected to the GPIO pins by default. These need to be disabled in many cases, by configuring those
pins as high- impedance inputs.
Table 7
Pin direction and pullup control
Shield
pin
Output enable GPIO (high = output)
Pullup enable GPIO
Pin
Linux
Power-on default
1
Pin
Linux
Power-on default
2
IO0
U34_ IO0.0
248
Pulled- down input
U39_IO0.0
216
Pulled up input
IO1
U34_ IO0.1
249
Pulled-down input
U39_IO0.0
217
Pulled up input
IO2
U34_ IO0.2
250
Pulled-down input
U39_IO0.0
218
Pulled up input
IO3
U34_ IO0.3
251
Pulled-down input
U39_IO0.0
219
Pulled up input
IO4
U34_ IO0.4
252
Pulled-down input
U39_IO0.0
220
Pulled up input
IO5
U34_ IO0.5
253
Pulled-down input
U39_IO0.0
221
Pulled up input
IO6
U34_ IO0.6
254
Pulled-down input
U39_IO0.0
222
Pulled up input
IO7
U34_ IO0.7
255
Pulled-down input
U39_IO0.7
223
Pulled up input
IO8
U34_ IO1.0
256
Pulled-down input
U39_IO0.7
224
Pulled up input
IO9
U34_ IO1.1
257
Pulled-down input
U39_IO0.7
225
Pulled up input
IO10
U34_ IO1.2
258
Pulled-down input
U39_IO0.7
226
Pulled up input
IO11
U34_ IO1.3
259
Pulled-down input
U39_IO0.7
227
Pulled up input
IO12
U34_ IO1.4
260
Pulled-down input
U39_IO0.7
228
Pulled up input
IO13
U34_ IO1.5
261
Pulled-down input
U39_IO0.7
229
Pulled up input
IO14
U16_ IO0.0
232
Pulled-down input
U17_ IO1.0
208
Pulled up input
IO15
U16_ IO0.1
233
Pulled-down input
U17_ IO1.1
209
Pulled up input
IO16
U16_ IO0.2
234
Pulled-down input
U17_ IO1.2
210
Pulled up input
IO17
U16_ IO0.3
235
Pulled-down input
U17_ IO1.3
211
Pulled up input
IO18
U16_ IO0.4
236
Pulled-down input
U17_ IO1.4
212
Pulled up input
IO19
U16_ IO0.5
237
Pulled-down input
U17_ IO1.5
213
Pulled up input
1 - These pins are externally pulled down inputs at power on. This effectively selects input direction for level shifters.
2 These pins are internally pulled up inputs at power- on. This effectively enables pullups (as 100 kohm + 47 kohm in series).
§
Intel® Edison Kit for Arduino*
Hardware Guide December 2014
12 33119 Document Number: 1- 004
Shield pin configuration
3 Level Functional Description High-
The Intel® Edison kit for Arduino*expansion board is designed to be hardware and software pin-compatible with
Arduino shields designed for the Uno R3. Digital pins 0 to 13 (and the adjacent AREF and GND pins), analog inputs
0 to 5, the power header, ICSP header, and the UART port pins (0 and 1) are all in the same locations as on the
Arduino Uno R3. This is also known as the Arduino 1.0 pinout. board Additionally, the Intel® Edison kit for Arduino*
includes a icro SD m card connector, a micro USB device port connected to UART2, and a combination micro USB
device connector and dedicated standard size USB 2.0 host Type- A connector (selectable via a mechanical
microswitch).
Figure 2 Intel® Edison kit for Arduino* block diagram
3.3 <- 5V > V Level
Translation provided
on board between
all Edison I/O and
Shield Headers
UART 2
Host USB
Full size
Type-A
USB 0TG
Client
USB
Micro
Type-B
7 1 V to 5 Brick
Power Supply
FLAS
H
ADC
SPI0
SPI
1 RX
4 ~IO3
7 ~IO6
5 IO4
6 ~IO5
8 IO7
3 IO2
2 TX
1 IO8
4 ~IO11
7 GND
5 IO12
6 IO13
8 AREF
3 ~IO10
2 ~IO9
9 SDA
10 SCL
VIN 8
5 5V
IOREF 2
3.3 4V
RESET 3
1
GND 6
GND 7
A5 6
A2 3
A1 2
A0 1
A3 4
A4 5
SD
Micro SD
Connector
UART 1
5V
VIN ( V)7 15 to
I2C
3.3V
DIGITAL ( ~)PWM
ANALOG IN POWER
GPIO
GPIO
SPI
2
6
6
2
4 ~ IO11
6 GND
2 5V
RESET 5
IO13 3
IO12 1
ICS P
IOREF Jumper
selects 3.3 5 or V
Shield Operation
Intel® Edison
FLASHMUX
Level
Shifter
Level Shifter Port
Expander
Port
Expander
I2C
DIR
GPIO
6
SEL &PUL L UP
Level Shifter
Level Shifter
FLASHMUX
2
4
Port
Expander
Port
Expander
DIR &PULL UP
JUMPER
SLECTION
3
I2C
3
USB MUX
Client
USB
Micro
Type-B
UART – USB
FTDI
Intel® Edison Kit for Arduino*
December 2014 Hardware Guide
Document Number: 331191- 004 13
Shield pin configuration
3.1 Intel® Edison kit for Arduino* header signal list
The Intel® Edison kit for Arduino* digital signals can be configured as input or output. When programmed as an
input, a GPIO can serve as an interrupt. The Intel® Edison kit for Arduino* 1.8 V I/O are translated to 3.3 or 5 V using
SN74LVC1T45 dual supply bus transceivers with 3 stat state if either supply rail ie outputs. Both outputs go tri s at
ground. V, The port di The driverection is referenced to VCCA. ±4 level for the transceiver is: mA at 1.8 ± 24 mA at
3.3 ± V, and 32 mA at 5 V.
Note: D rive level at 1.8 V is for reference only – . pertains to drive level towards the Intel® Edison compute module
Table 8 Intel® Edison kit for Arduino* header signal list
Header Arduino pin name Signal function
Power
N/C
Not connected
Power
IOREF Shield I/O reference voltage (select 3.3 or 5 V via jumper on board)
Power
RESET Shield reset (programmable via software or manual push button)
Power
3.3 V
System 3.3 V output
Power
5 V
System 5 V output
Power
GND
Ground
Power
GND Ground
Power
VIN V) System input power (7 to 15
Analog
A0
Analog input or digital I/O
Analog
A1
Analog input or digital I/O
Analog
A2
Analog input or digital I/O
Analog
A3
Analog input or digital I/O
Analog
A4 / SDA Analog input, digital I/O, or I2C data (also connected to digital header)
Analog
A5 / SCL Analog input, digital I/O, or I
2
C data (also connected to digital header)
Digital
SCL
I2C clock
Digital
SDA
I2C data
Digital
AREF
ADC reference voltage (select AREF or IOREF via jumper J8 on board)
Digital
GND Ground
Digital
13 / SCK Digital I/O, or SPI clock
Digital
12 / MISO Digital I/O, or SPI receive data
Digital
~11 / MOSI
Digital I/O, SPI send data, or PWM (configured with PWM swizzler)
Digital
~10
Digital I/O, SPI signal select, or PWM (configured with PWM swizzler)
Digital
~9
Digital I/O, PWM (configured with PWM swizzler)
Digital
8 Digital I/O
Digital
7 Digital I/O
Digital
~6
Digital I/O, PWM (configured with PWM swizzler)
Digital
~5
Digital I/O, PWM (configured with PWM swizzler)
Digital
4
Digital I/O
Digital
~3 Digital I/O, PWM (configured with PWM swizzler)
Digital
2 Digital I/O
Digital
1 / TX Digital I/O
Digital
0 / RX
Digital I/O
ICSP
MISO
SPI receive data (connected to digital pin 12)
ICSP
5V
System 5 V output
ICSP
SCK SPI clock (connected to digital pin 13)
ICSP MOSI SPI send data (connected to digital pin 11)
ICSP
RESET
Shield reset (programmable via software or manual push button)
ICSP
GND
Ground
Intel® Edison Kit for Arduino*
Hardware Guide December 2014
14 33119 Document Number: 1- 004
Shield pin configuration
3.2 Intel® Edison kit for Arduino* PWM swizzler
There are four available GPIO that can be configured as PWM outputs. The PWM features are:
• The PWM Output Frequency and Duty Cycle can be estimated by the equations:
• Target frequency ~= 19.2 / MHz * Base_unit value 256
• Target PWM Duty Cycle ~= PWM_on_time_divisor / 256
The four PWM sources are wired to a PWM “swizzler”. This pin header arrangement allows the four PWM sources to
be routed to any four of the six Arduino header pins. Figure 3 shows the PWM swizzler.
Figure 3 Intel® Edison kit for Arduino* PWM swizzler
The four PWM sources from the Intel® Edison GP12_PWM0, GP13_PWM1, GP182_PWM2, and compute module (
GP183_PWM3) can be configured to drive four of the six * Arduino header PWMs. Each Intel® Edison kit for Arduino
PWM can be jumpered to one , of three Arduino PWMs. For example GP12_PWM0 can be jumpered to PWM0_OUT,
PWM2_OUT, or PWM1_OUT.
Arduino* s multiplexing has secondary multiplexing options of SPI (or GPIO). No other PWM ha these secondary
multiplexing options. Therefore, if the four Intel® Edison compute mod PWMs are used and ule are not connected to
the first four Arduino* PWM pins, then those unused pins of the first four pins cannot be used as a GPIO. They will
have any function they cannot be input; s ( 9 or outputs Table ).
Table 9 Intel® Edison kit for Arduino* PWM swizzler signal assignments
Digital pin Uno Uno Edison I/O Edison PWM
11
IO PWM(5)
GP43 (SSP2_TXD)
PWM3
10
IO PWM(4)
GP41 (SSP2_FS0)
PWM3, PWM2
9
IO PWM(3)
GP183_PWM3
PWM3, PWM2, PWM1
6 IO PWM(2)
GP182_PWM2
PWM2, PWM1, PWM0
5
IO PWM(1)
GP13_PWM1
PWM1, PWM0
3
IO PWM(0)
GP12_PWM0
PWM0
The factory default jumper configuration of Intel® Edison kit for Arduino* has digital pins 3, 5, 6, and 9 attached to
GPx_PWMx. These pins can be configured to be either a GPIO or a PWM output. The swizzler allows the four Intel®
Edison c m * 9ompute odule PWMs to be mapped to the six Arduino pins as shown in the last column of Table . For
example, if PWM0 is mapped to digital pin 5, then there is no kit for Arduino* Intel® Edison pin available to connect
to Digital pin 3. So this pin no longer has a function. If it is driven as a If it is driven as an n output, it will output high.
input, the signal is lost in the swizzler.
The default configuration is DIG3 = GP12_PWM0, DIG5 = GP13_PWM1, DIG6 = GP182_PWM2, DIG9 = and
GP183_PWM3. This requires jumpers on J12 1-2, and J12 3 11 1 2, and J11 3-4, J - -4 4. , as shown in Figure
Intel® Edison Kit for Arduino*
December 2014 Hardware Guide
Document Number: 331191- 004 15
Shield pin configuration
Figure 4 PWM swizzler on the Intel® Edison kit for Arduino*
3.3 Intel® Edison kit for Arduino* analog inputs
The analog inputs are fed to an ADS7951 A/D converter. This device has the following features:
• 20 M Hz clock rate
• 12- bit A/D conversion
• 1 MHz sample rate
• 70 dB signal to noise ratio
• 0 to 2.5 V or 0 to 5 IOREF via jumper J8 onboard) V input range (select either AREF or
The analog inputs are multiplexed with digital I/O using SN74LVC2G53 analog switches. These switches isolate the
digital I/O from the analog input to prevent crosstalk. The SN74LVC2G53 also has an inhibit pin that places the I/O
in a tristate condition. The switch also has low on state resistance of 15 ohm at 4.5 V VCC.
3.4 Intel® Edison kit for Arduino* signal pullup resistors
The analog and digital pins can be configured to have an external pull-up resistor connected. The pullup value is
fixed at 47 . kohm
3.5 Intel® Edison kit for Arduino* USB interface
The Intel® Edison c mompute odule has a single USB 2.0 interface. This interface is the primary method for
downloading code. The Intel® Edison compute module is designed to support OTG, using the ID signal. Circuitry on
the Intel® Edison kit for Arduino* board uses a USB multiplexer, and an external switch to configure the USB
interface as a host port or device port. SW1 is a slider switch which selects between host mode and device mode.
When the slider is switched towards the USB standard size Type A connector, the Intel® Edison compute module
will go to host mode. When the switch is towards the micro USB Type B connector, the Intel® Edison compute
module will go to device mode.
Note: USB host mode always requires use of an external power adapter.
Intel® Edison Kit for Arduino*
Hardware Guide December 2014
16 33119 Document Number: 1- 004
Shield pin configuration
3.6 Intel® Edison kit for Arduino* power supply
The Intel® Edison compute module is a low power device. In general it will not draw more than 200 mA
(approximately 430 mA (final value TBD) when transmi Fi) from the main power source tting over Wi- . Therefore, the
Intel® Edison kit for Arduino* may run on USB power (when configured as a device), or off an external power
adapter from 7 to 15 V.
Power from the external power adapter goes to a DC-DC converter and down converted to 5 V. The 5 V rail is
diode- - ORed with the USB micro B VBUS rail. This power goes to a DC DC converter which down converts the power
to 4.4 Edison compute module V. This voltage is in the safe range for the Intel® VSYS. The VSYS power range is
3.15 V min to 4.5 V max. This allows VSYS to run off a standard lithium ion battery.
The onboard charger IC is configured to detect the input power source and to limit the input power to either
500 mA (if connected to USB micro B port) or up to 1 A if connected to the DC power jack. The charger is
programmed to charge at 100 . This charger is designed to charge standard lithium ion batteries with 4.2 mA V
maximum charging voltage. End- users are responsible for choosing a suitable battery and following all safety
precautions, to assure overcharging or charging when the battery temperature is too high is avoided.
For low power applications (those shields running off 3.3 Vmax) can be attached V) a lithium ion battery (3.0 to 4.3
to J2, which will power mA the Intel® Edison kit for Arduino and provide 100 of 3.3 V to the shield.
Some considerations of the power distribution in the Intel® Edison kit for Arduino*:
• Due to the diode ORing of the 5 V V DC/DC and the VBUS input, means the 5 power to the shield header will
be nominally below 5 V. In the case of VBUS the voltage may be as low as 4.4 V (4.75 V VBUS min – 0.3 V
diode drop. In the case of external power adapter 4.7 V.
• USB host mode always requires use of an external power adapter.
3.7 Intel® Edison kit for Arduino* expansion mechanicals
Figure 5 lists the dimensions (in thousands of inches and [mm]) of the Intel® Edison kit for Arduino* board.
Figure 5 d s Intel® Edison kit for Arduino* mechanical imension
DS3
DS1
DS2
§
Intel® Edison Kit for Arduino*
December 2014 Hardware Guide
Document Number: 331191- 004 17
Shield pin configuration
4 the Intel® Edison kit for Arduino* Powering
You can power the Intel® using any of the followingEdison kit for Arduino* :
• a ; n external power supply on J1
• DCIN via shield header pin VIN;
• a USB cable via micro USB connector J16; or
• a - lithium ion battery connected to J2.
When power is applied to J1 or VIN, the external power must be in the range of 7 V. The power is converted to 17
to 5 V via a switching power supply, which powers the rest of the system. This supply was designed for a 1 A
continuous supply. Higher currents will generate more power losses and may thermally damage the switcher. The
switcher does have internal short circuit protection, and thermal shutdown protection. The end hould not -user s
rely on thermal not short circuit protection.
Figure 6 he power distribution network of the shows t Intel® Edison kit for Arduino*.
Figure 6 Intel® Edison kit for Arduino* power distribution network
Power from the 5 -V switcher is diode ORed with power from the USB connector. This arrangement allows the Intel®
Edison kit for Arduino* to run off external power or USB power. This rail is used to power the shields, the SD card
slot, and a 4.35 V switcher. The total current on this rail should be limited to 1 A maximum continuous.
The 4.35 V rail powers a battery charger and the Intel® Edison compute module. The 4.3 V supply is also designed
to generate 1 A, and has the same protections (thermal and short circuit) as the 5 V supply.
The charger is designed to only accept 1 A. The mA maximum from the 4.35 V rail, and will charge a battery at 100
charger will supply power from the 4.35 V input or from the battery (if attached). The charger will charge the
battery (from the 4.35 V supply) autonomously using whatever power is left over from powering the Intel® Edison
kit for Arduino.
For low voltage systems, the Intel® mA to the shields. The user Edison compute module can provide 3.3 V at 250
should limit the current from the Intel® Edison kit for Arduino* 3.3 V rail. Higher currents will cause the 3.3 V output
to droop (due to IR losses), and Edison compute module may cause excessive heating of the Intel® .
The Intel® Edison compute module mA. During Wiis a low power device. It normally operates at 200 -Fi transmit
bursts, the current could reach 600 mA for milliseconds. The sum of the Intel® Edison kit for Arduino* current,
recharging, SD card, and shield power could exceed the 500 mA specification. This could cause triggering of the
USB power switch within a PC, causing loss of USB functionality until the PC is restarted.
Intel® Edison Kit for Arduino*
Hardware Guide December 2014
18 33119 Document Number: 1- 004
Shield pin configuration
Some considerations of the power distribution in the Intel® Edison kit for Arduino*:
• There is a diode ORing of the 5 V DC/DC and the VBUS input. In the case of powering the Intel® Edison kit for
Arduino* from VBUS, the shield voltage may be as low as 4.4 V (4.75 V VBUS min – 0.3 V diode drop). In the
case of external power adapter, voltage to the shield will be 5 V ±2%.
• Using the Intel® Edison compute module as a USB HOST requires use of an external adapter.
• End-users are responsible for choosing a suitable battery and following all safety precautions, to prevent
overcharging or charging when the battery temperature is too high. The battery should be at least 200 mAH
capacity due to the 100 mA charging current. We recommend battery packs with internal protection circuits.
4.1 Boot voltage selection – DCIN signal
DCIN is a signal is being powerthat indicates whether the Intel® Edison compute module ed from a battery or from
an external power source. DCIN also sets the voltage level required on VSYS in order to boot. When DCIN is floating
or tied to ground, the voltage on VSYS must rise from 2.5 to 3.5 ; V in 10 ms otherwise the boot is aborted. When
the boot is aborted, power must be cycled below 2.5 V. If DCIN is connected to VSYS, the Intel® Edison compute
module . will start to boot when VSYS is above 2.5 V for 100 ms
Note: When DCIN is connected to VSYS, whenever the voltage is above 2.8boot will occur msV for 100 . The
DCIN signal is attached to VSYS on the PCB.
Note: T -Fi he absolute minimum voltage to assure Wi and Bluetooth functionality is 3.15 V.
§
Intel® Edison Kit for Arduino*
December 2014 Hardware Guide
Document Number: 331191- 004 19
Shield pin configuration
5 Batteries
The rechargers chosen on the Intel® Edison kit for Arduino* Intel® Edison and the Breakout Board were designed for
lithium lithium-ion or - ’ polymer batteries. Follow the manufacturer s guidelines when charging batteries. Generally,
charging current should not exceed 50 to 70% of the rated capacity. For example, a 200 mAH battery should be
charged with 70% mA •200 = (140 mA ).
The the reakout Intel® Edison k * mA ; it for Arduino has a 100 charging current Intel® Edison B B mA oard has a 190
charging current.
§
Intel® Edison Kit for Arduino*
Hardware Guide December 2014
20 33119 Document Number: 1- 004
Shield pin configuration
6 Layout
6.1 Antenna keepout
The area under and around the antenna should be kept free of all components, routes, and ground plane. The
Intel® Edison compute module DXF in white with antenna keepout shown in the Arduino* trace layers. See Figure 7.
Figure 7 Area around antenna
6.2 Layout SD card, I2S, SPI, I2C
Table 10 Layout SD card
Signal parameter Metric (mm) Standard (mils)
Total length L1
0.254 to 101.6 10 to 4000 mm mils
DATA/CMD/CTRL to CLK maximum pin-to- pin length mismatch
±2.54 mm ±100 mils
Minimum main route spacing ratio
60 × 60
µ
m. 1:1 trace width/space.
CLK to DATA/CMD/CTRL matching
±200 mils
Characteristic single ended impedance
42 to 45 ohm (±10%)
Load capacitance
2 to 5 pF
Note: 1) For SPI, total length is 6000 mils.
2) For I2C, total length is 8000 mils.
Intel® Edison Kit for Arduino*
December 2014 Hardware Guide
Document Number: 331191- 004 21
Shield pin configuration
6.3 LEDs
The Intel® Edison kit for Arduino has three LEDs. (See Figure 5 for locations.)
• DS1 is the reset LED. It will turn on when the Intel® Edison processor is running. When the processor is in
reset and asserting RESET_OUT# low, it will turn off.
• DS2 is the standard LED on the Arduino* board. It runs using the ‘blink’ code or whenever Digital I/O 13 is
asserted High. It can be used as an indicator under direct control.
• DS3 is the battery charging LED. It will turn on when the LTC4067 is charging an attached battery.
§
Intel® Edison Kit for Arduino*
Hardware Guide December 2014
22 33119 Document Number: 1- 004
Shield pin configuration
7 Handling
When assembling an Intel® handle the Edison compute module to an Arduino* board, Intel® Edison compute
module by the PCB edges. Avoid holding or exerting pressure to the shields. To mate the Intel® Edison compute
module to the Arduino* board, apply pressure directly above the connector and to the left corner, as shown in
Figure 8.
Figure 8 Inserting an Intel® Edison compute module
§
Intel® Edison Kit for Arduino*
December 2014 Hardware Guide
Document Number: 331191- 004 23
Shield pin configuration
8 Debug UART and Low-Power Sleep Mode
When the Intel® Edison compute module goes into low-power sleep, the UART internal FIFO and interface is
powered down. - x xTherefore, a two wire UART (R /T ) will lose the first received character whenever the Intel® Edison
compute module sleep mode. In order to avoid this condition, when sleep mode is enabled, a four -is in low power -
wire UART (R and RTS) is required.x, Tx, CTS,
Note: Low- ipower sleep mode is disabled by default n the latest image. To address this, update your firmware as
explained . in the Getting Started Guide at https://communities.intel.com/docs/DOC-23147
§
Intel® Edison Kit for Arduino*
Hardware Guide December 2014
24 33119 Document Number: 1- 004
Shield pin configuration
9 Buttons
This section explains s the software functionality of the Intel® Edison kit for Arduino* button .
The Intel® Edison has the following buttons: kit for Arduino*
• System reset. Pressing the system reset button (SW1UI5) will reset the Intel® Edison compute module, and
reset the I/O expanders, setting all the shield pins to high impedance state with no pullups.
• Shield reset. Pressing the shield reset button (SW1UI1) will pull the shield signal reset to the active low
state. It does not affect the state of the Intel® Edison compute module or its I/O.
• Power button. The power button (SW1UI2) is configured by software. In general, pressing and holding this
button will cause the Intel® Edison compute module to power down. (It will leave the I/O configuration in the
port expanders in its current state.) Pressing this button momentarily when the Intel® Edison compute
module is powered down (but power is still applied) will cause the Intel® Edison compute module to reboot.
If the Intel® the Intel® Edison compute module is running, then a momentary press will cause Edison
compute module to go into low power sleep mode. Pressing the button momentarily when the Intel® Edison
compute module Edison compute module is asleep, will bring the Intel® into full power mode. You must
press and hold SW1U15 for 8 seconds to reset the Intel® . Pressing the reset button Edison compute module
for 4 seconds will restart the Intel® Edison compute module.
9.1 FWR_RCVR and RCVR_MODE
SW1UI3 and SW1UI4 are for factory use only.
§
Intel® Edison Kit for Arduino*
December 2014 Hardware Guide
Document Number: 331191- 004 25
Shield pin configuration
10 Digikey sources
Figure 9 shows some third- party accessories you can use.
Figure 9 Digikey sources
Mating connector 2.0 mm
DF40C(2.0) 0.4V(51) H11908CT- -70DS - -ND Cut tape
DF40C(2.0) 0.4V(51) H11908TR- -70DS -ND Tape and Reelt
Mini- - -SMT- breakout power jack PJ 002BH TR
CP-002BHPJCT- ND Cut tape
PJ- - - -002BH SMT TR CP 002BHPJTR-ND Tape and reel
Mini- breakout USB adapter cable
USB A female to Micro A male 10 00649 839 1105- - -ND
Mini- breakout male header
2x14 M20-9980745 952-1932-ND
§
Intel® Edison Kit for Arduino*
Hardware Guide December 2014
26 33119 Document Number: 1- 004
Shield pin configuration
11 Shield pin configuration
This chapter will help you configure the Arduino shield pins. *
To configure the Arduino* shield pins, do the following:
1. IO19. Identify the Arduino to use, in the range IO0* shield pin number of the pin you want -
2. Identify the functions available for the given pin, and select the function you want to use. Typical functions
are GPIO, PWM, UART, I2C, SPI, ADC. Only some functions are available on each pin.
3. Determine which GPIO signals, if any, need to be configured to select the correct pin muxing option for the
selected function. Some pins only have a single function, or do not require mux control.
4. Determine which GPIO signals, if any, need to be configured to select the pin buffer direction for input or
output, and determine the direction that is required.
5. Determine which GPIO signals, if any, need to be configured to select the pullup resistor control, and
whether the pullup resistor should be enabled or disabled. For most pin functions, the pullup resistors
should typically be disabled. For GPIO input functions, the pullup resistor may optionally be enabled or
disabled, your needs. according to
6. Export the above GPIO numbers for access in the Linux user-space environment (from the command
shell).
7. Configure the above GPIO numbers for output.
8. Assert the TRI_STATE_ALL signal to disconnect the shield pins.
9. Set the above GPIO numbers to assert their output logic levels as high or low.
10. Set the SoC GPIO pin mode for the required functionality.
11. Deassert the TRI_STATE_ALL signal to reconnect the shield pins.
11.1 Configure IO5 as a GPIO input, with pullup resistor disabled
To configure IO5 as a GPIO input, with pullup resistor disabled, do the following:
1. Refer to Table Table 2 for the GPIO number. According to 2 , the GPIO number for IO5 is 13.
2. According to 4 - . Table , GPIO 43 pin mux must be set to mode0 to select the GPIO
3. According to Table 7 , GPIO 253 must be set to 0 to disable the output direction for IO5.
4. According to Table 7 -, GPIO 221 must be set as a high impedance input to disable the external pullup
resistor for IO5.
5. According to Table 6, the TRI_STATE_ALL signal is controlled by GPIO 214.
After you have gathered all of this information, enter the following commands in Linux:
# echo 13 > /sys/class/gpio/export
# echo 253 > /sys/class/gpio/export
# echo 221 > /sys/class/gpio/export
# echo 214 > /sys/class/gpio/export
# echo high > /sys/class/gpio/gpio214/direction
# echo low > /sys/class/gpio/gpio253/direction
# echo in > /sys/class/gpio/gpio221/direction
# echo mode0 > /sys/kernel/debug/gpio_debug/gpio13/current_pinmux
# echo in > /sys/class/gpio/gpio13/direction
# echo low > /sys/class/gpio/gpio214/direction
Y ou should be able to use IO5 as a GPIO input. For example:
# cat /sys/class/gpio/gpio13/value
Intel® Edison Kit for Arduino*
December 2014 Hardware Guide
Document Number: 331191- 004 27
Shield pin configuration
11.2 Configure IO11 as a GPIO input, with pullup resistor disabled
To configure IO11 as a GPIO input, with pullup resistor disabled, do the following:
1. Refer to Table Table 2 for the GPIO number. According to 2 , the GPIO number for IO11 is 43.
2. According to Table 4, GPIO 262 must be set to 1 to select GPIO/SPI, GPIO 241 must be set to 0 to select
GPIO, and GPIO 43 pin mux must be set to ‘mode0’ to select GPIO. -
3. According to Table 7 , GPIO 259 must be set to 0 to disable the output direction for IO11.
4. According to Table 4, GPIO 227 must be set as a high-impedance input to disable the external pullup
resistor for IO5.
5. According to Table 6, the TRI_STATE_ALL signal is controlled by GPIO 214.
After you have gathered all of this information, enter the following commands in Linux:
# echo 43 > /sys/class/gpio/export
# echo 262 > /sys/class/gpio/export
# echo 241 > /sys/class/gpio/export
# echo 259 > /sys/class/gpio/export
# echo 227 > /sys/class/gpio/export
# echo 214 > /sys/class/gpio/export
# echo high > /sys/class/gpio/gpio214/direction
# echo high > /sys/class/gpio/gpio262/direction
# echo low > /sys/class/gpio/gpio241/direction
# echo mode0 > /sys/kernel/debug/gpio_debug/gpio43/current_pinmux
# echo low > /sys/class/gpio/gpio259/direction
# echo in > /sys/class/gpio/gpio227/direction
# echo in > /sys/class/gpio/gpio43/direction
# echo low > /sys/class/gpio/gpio214/direction
Y ou should be able to use IO11 as a GPIO input. For example:
# cat /sys/class/gpio/gpio43/value
11.3 Configure a IO7 as GPIO input, with pullup
resistor enabled
To configure IO7 as resistor a GPIO input, with pullup enabled, do the following:
1. Refer to Table Table 2 for the GPIO number. According to 2 , the GPIO number for IO7 is 48.
2. According to Table 7 , GPIO 255 must be set to 0 to disable the output direction for IO7.
3. According to Table 7 , GPIO 223 must be set to output high to enable the external pullup resistor for IO7.
4. According to Table 6, the TRI_STATE_ALL signal is controlled by GPIO 214.
After you have gathered all of this information, enter the following commands in Linux:
# echo 48 > /sys/class/gpio/export
# echo 255 > /sys/class/gpio/export
# echo 223 > /sys/class/gpio/export
# echo 214 > /sys/class/gpio/export
# echo high > /sys/class/gpio/gpio214/direction
# echo low > /sys/class/gpio/gpio255/direction
# echo high > /sys/class/gpio/gpio223/direction
# echo in > /sys/class/gpio/gpio48/direction
# echo low > /sys/class/gpio/gpio214/direction
You should be able to use IO7 as a GPIO input. For example:
# cat /sys/class/gpio/gpio48/value
Intel® Edison Kit for Arduino*
Hardware Guide December 2014
28 33119 Document Number: 1- 004
Shield pin configuration
11.4 Configure a IO6 as PWM output
To configure IO6 as a PWM output, do the following:
1. Refer to Table Table 2 for the GPIO number. According to 2 , the GPIO number for IO6 is 182.
2. According to Table 4, GPIO 182 pin- mux must be set to ‘mode1’ to select PWM.
3. According to Table 7 , GPIO 254 must be set to 1 to enable the output direction for IO6.
4. According to Table 7, GPIO 222 must be set as a high-impedance input to disable the pullup resistor for IO6.
5. According to Table 6, the TRI_STATE_ALL signal is controlled by GPIO 214.
After you have gathered all of this information, enter the following commands in Linux:
# echo 254 > /sys/class/gpio/export
# echo 222 > /sys/class/gpio/export
# echo 214 > /sys/class/gpio/export
# echo high > /sys/class/gpio/gpio214/direction
# echo high > /sys/class/gpio/gpio254/direction
# echo in > /sys/class/gpio/gpio222/direction
# echo mode1 > /sys/kernel/debug/gpio_debug/gpio182/current_pinmux
# echo low > /sys/class/gpio/gpio214/direction
You should be able to use IO6 as a PWM output. For example:
# echo 2 > /sys/class/pwm/pwmchip0/export
# echo 2000000 > /sys/class/pwm/pwmchip0/pwm2/duty_cycle
# echo 1 > /sys/class/pwm/pwmchip0/pwm2/enable
11.5 Configure IO14 as an ADC input
To configure IO14 as an ADC input, do the following:
1. Refer to Table Table 2 for the GPIO number. According to 2 , the GPIO number for IO14 is 44.
2. According to Table 4 , GPIO 200 must be set to 1 to select ADC.
3. According to Table 7 , GPIO 232 must be set to 0 to disable the output direction for IO14.
4. Any GPIO lines directly connected to IO14 should be configured as high-impedance inputs to prevent
possible current leakage. According to Table 7 , GPIO 208 is used to enable a pullup resistor for IO14.
5. According to Table 6, the TRI_STATE_ALL signal is controlled by GPIO 214.
A fter you have gathered all of this information, enter the following commands in Linux:
# echo 200 > /sys/class/gpio/export
# echo 232 > /sys/class/gpio/export
# echo 208 > /sys/class/gpio/export
# echo 214 > /sys/class/gpio/export
# echo high > /sys/class/gpio/gpio214/direction
# echo high > /sys/class/gpio/gpio200/direction
# echo low > /sys/class/gpio/gpio232/direction
# echo in > /sys/class/gpio/gpio208/direction
# echo low > /sys/class/gpio/gpio214/direction
You should be able to use IO14 as an ADC input. For example:
# cat /sys/bus/iio/devices/iio:device1/in_voltage0_raw
Note: The default state of the mux switches and level-shifters for shield pins IO11 to 13 is inconsistent, and will
impair SPI communication to the ADC if not configured properly. Thus, we recommend following the
instructions elsewhere in this document to fully configure these pins for any of their functions (for
example, SPI or GPIO) before attempting to use the ADC.
Intel® Edison Kit for Arduino*
December 2014 Hardware Guide
Document Number: 331191- 004 29
Shield pin configuration
11.6 Configure IO18/IO19 Ifor 2C connectivity
To configure IO18 and IO19 for I2C connectivity, do the following:
1. Refer to Table Table 2 for the GPIO numbers. According to 2, the GPIO numbers for IO18 and IO19 are 28
and 27, respectively.
2. According to Table 4, GPIO 204 must be set to 1 to select GPIO/I
2C, and GPIO 28 pin mux must be set to -
‘mode1’ to select I2C for IO18.
3. According to Table 4 -, GPIO 205 must be set to 1 to select GPIO/I2C, and GPIO 27 pin mux must be set to
‘mode1’ to select I2C for IO19.
4. GPIO 14 and GPIO 165 are also connected to the I
2
C signals, and should be configured as high-
impedance inputs when I2C is in use on these pins, to prevent them driving a signal on the I
2C bus.
5. According to Table 7, GPIO 236 must be set to 0 to disable the output direction for GPIO 14, and GPIO 237
must be set to 0 to disable the output direction for GPIO 165.
6. According to impedance inputTable 7 -, GPIO 212 and 213 must be set as high s to disable the pullup
resistors for IO18 and IO19, respectively.
7. According to Table 6, the TRI_STATE_ALL signal is controlled by GPIO 214.
After you have gathered all of this information, enter the following commands in Linux:
# echo 28 > /sys/class/gpio/export
# echo 27 > /sys/class/gpio/export
# echo 204 > /sys/class/gpio/export
# echo 205 > /sys/class/gpio/export
# echo 236 > /sys/class/gpio/export
# echo 237 > /sys/class/gpio/export
# echo 14 > /sys/class/gpio/export
# echo 165 > /sys/class/gpio/export
# echo 212 > /sys/class/gpio/export
# echo 213 > /sys/class/gpio/export
# echo 214 > /sys/class/gpio/export
# echo high > /sys/class/gpio/gpio214/direction
# echo high > /sys/class/gpio/gpio204/direction
# echo high > /sys/class/gpio/gpio205/direction
# echo in > /sys/class/gpio/gpio14/direction
# echo in > /sys/class/gpio/gpio165/direction
# echo low > /sys/class/gpio/gpio236/direction
# echo low > /sys/class/gpio/gpio237/direction
# echo in > /sys/class/gpio/gpio212/direction
# echo in > /sys/class/gpio/gpio213/direction
# echo mode1 > /sys/kernel/debug/gpio_debug/gpio28/current_pinmux
# echo mode1 > /sys/kernel/debug/gpio_debug/gpio27/current_pinmux
# echo low > /sys/class/gpio/gpio214/direction
You should be able to use IO18 and IO19 for I
2C communication.
Intel® Edison Kit for Arduino*
Hardware Guide December 2014
30 33119 Document Number: 1- 004
Shield pin configuration
11.7 Configure IO10 through IO13 for SPI connectivity
To configure IO10 through IO13 for SPI connectivity, do the following:
1. Refer to Tabl Tablee 2 for the GPIO numbers. According to 2 3 , the GPIO numbers for IO10 through IO1 are
111, 115, 114, and 109, respectively.
2. According to Table 4, GPIO 263 must be set to 1 to select GPIO/SPI, GPIO 240 must be set to 1 to select
SPI, and GPIO 111 pin- mux must be set to ‘mode1’ to select SPI for IO10.
3. According to Table 4, GPIO 262 must be set to 1 to select GPIO/SPI, GPIO 241 must be set to 1 to select
SPI, and GPIO 115 pin- mux must be set to ‘mode1’ to select SPI for IO11.
4. According to Table 4 -, GPIO 242 must be set to 1 to select SPI, and GPIO 114 pin mux must be set to
‘mode1’ to select SPI for IO12.
5. According to Table 4 -, GPIO 243 must be set to 1 to select SPI, and GPIO 109 pin mux must be set to
‘mode1’ to select SPI for IO13.
6. According to Table 7, GPIO 258 must be set to 1 to enable the output direction for IO10, GPIO 259 must
be set to 1 to enable the output direction for IO11, GPIO 260 must be set to 0 to disable the output
direction for IO12, and GPIO 261 must be set to 1 to enable the output direction for IO13.
7. According to Table 7 -, GPIOs 226 through 229 must be set as high impedance inputs to disable the pullup
resistors for IO10 through IO13.
8. According to Table 6, the TRI_STATE_ALL signal is controlled by GPIO 214.
9. After you have gathered all of this information, enter the following commands in Linux:
# echo 111 > /sys/class/gpio/export
# echo 115 > /sys/class/gpio/export
# echo 114 > /sys/class/gpio/export
# echo 109 > /sys/class/gpio/export
# echo 263 > /sys/class/gpio/export
# echo 240 > /sys/class/gpio/export
# echo 262 > /sys/class/gpio/export
# echo 241 > /sys/class/gpio/export
# echo 242 > /sys/class/gpio/export
# echo 243 > /sys/class/gpio/export
# echo 258 > /sys/class/gpio/export
# echo 259 > /sys/class/gpio/export
# echo 260 > /sys/class/gpio/export
# echo 261 > /sys/class/gpio/export
# echo 226 > /sys/class/gpio/export
# echo 227 > /sys/class/gpio/export
# echo 228 > /sys/class/gpio/export
# echo 229 > /sys/class/gpio/export
# echo 214 > /sys/class/gpio/export
# echo high > /sys/class/gpio/gpio214/direction
# echo high > /sys/class/gpio/gpio263/direction
# echo high > /sys/class/gpio/gpio240/direction
# echo high > /sys/class/gpio/gpio262/direction
# echo high > /sys/class/gpio/gpio241/direction
# echo high > /sys/class/gpio/gpio242/direction
# echo high > /sys/class/gpio/gpio243/direction
# echo high > /sys/class/gpio/gpio258/direction
# echo high > /sys/class/gpio/gpio259/direction
# echo low > /sys/class/gpio/gpio260/direction
# echo high > /sys/class/gpio/gpio261/direction
# echo in > /sys/class/gpio/gpio226/direction
# echo in > /sys/class/gpio/gpio227/direction
Intel® Edison Kit for Arduino*
December 2014 Hardware Guide
Document Number: 331191- 004 31
Shield pin configuration
# echo in > /sys/class/gpio/gpio228/direction
# echo in > /sys/class/gpio/gpio229/direction
# echo mode1 > /sys/kernel/debug/gpio_debug/gpio111/current_pinmux
# echo mode1 > /sys/kernel/debug/gpio_debug/gpio115/current_pinmux
# echo mode1 > /sys/kernel/debug/gpio_debug/gpio114/current_pinmux
# echo mode1 > /sys/kernel/debug/gpio_debug/gpio109/current_pinmux
# echo low > /sys/class/gpio/gpio214/direction
You should be able to use IO10 through IO13 for SPI connectivity.
§
Intel® Edison Kit for Arduino*
Hardware Guide December 2014
32 33119 Document Number: 1- 004

Product specificaties

Merk: Intel
Categorie: Niet gecategoriseerd
Model: Edison Breakout Board
Hoogte: 3.9 mm
Productnaam: Intel Edison Breakout Board
Bluetooth: Ja
Gyroscoop: Ja
Versnellingsmeter: Ja
Frequentie van processor: 500 MHz
Processormodel: Intel Atom®
64-bit computing: Nee
Wi-Fi-standaarden: 802.11a, 802.11b, 802.11g
Bluetooth-versie: 4.0
Vormfactor: 25mm x 35.5mm
Inclusief besturingssysteem: Yocto Linux 1.6
Ethernet LAN: Nee
Compatibele geheugenkaarten: SD, SDHC
Processor lithografie: 22 nm
DC voltage input: 3.15 - 4.5 V
Aantal USB-aansluitingen: 1
USB-versie: 2.0
Bluetooth Low Energy (BLE): Ja
Intern geheugentype: LPDDR3
USB On-The-Go ondersteuning: Ja
Processor socket: 70-pin Hirose .4mm
ECC ondersteund door processor: Nee
Maximum intern geheugen: 4 GB
Ingebouwde grafische adapter: Nee
Intel® Flex Memory Access: Nee
Intel® AES New Instructions (Intel® AES-NI): Nee
CPU configuratie (max): 1
Ingebouwde opties beschikbaar: Nee
Intel® Virtualization Technology for Directed I/O (VT-d): Nee
Intel® Clear Video-technologie: Nee
Verpakkingsgrootte processor: 25mm x 35.5mm mm
Intel® Trusted Execution Technology: Ja
Intel® Anti-Theft Technology (Intel® AT): Nee
Frequentiebereik: 2.4 - 5 GHz
Output current: 100 mA
Spanning: 1.8 V
Flash memory: 4096 MB
Maximaal intern geheugen ondersteund door processor: 4 GB
ECC: Nee
Kloksnelheid geheugen: 800 MHz
Trusted Platform Module (TPM): Nee
Export Control Classification Number (ECCN): EAR99
Aansluiting(en): UART, SPI, GPIO
Maximaal intern geheugen: 4096 MB
FSB Parity: Nee
Physical Address Extension (PAE): Ja
Intel® vPro™ Platform Eligibility: Nee
Intel® Dual Display Capable Technology: Nee
Intel® Rapid Storage Technology: Nee
Intel® Fast Memory Access: Nee
Geheugen kanaal: Dubbelkanaals
Bewegingssensor: Ja
Seriële poort(en): 2
Intel® High Definition Audio (Intel® HD Audio): Nee
Geheugenbus: 32 Bit
Ondersteunde geheugen types: DDR3-SDRAM
Wifi: Ja
Bedrijfstemperatuur (T-T): 0 - 40 °C
Type product: 11
Intel® Matrix Storage Technology (Intel® MST): Nee
Intel® Active Management Technology (Intel® AMT): Nee
Code geharmoniseerd systeem (HS): 8473301180
Soort flashgeheugen: NAND
Commodity Classification Automated Tracking System (CCATS): NA
Parallele port via interne header: Nee
Audiokanalen: 1
Consumer Infrared Headers: Nee
Marktsegment: Desktop
Seriële port via interne header: Ja
Back-to-BIOS button: Nee
Model microcontroller: Intel® Quark
Aantal digitale I/O pinnen: 14
Aantal analoge I/O pinnen: 6
Afmetingen bord: 25 x 35.5 mm
Geïntegreerde LAN: Nee
Moederbord ARK ID: 84575
Audio port type: I2S
Ingebouwde wifi: Yes, 802.11n
Lage halogeen opties beschikbaar: Nee
Lanceringsdatum: Q3'14
Intel® Remote Wake Technology (Intel® RWT): Nee
Intel® Remote PC Assist Technology (RPAT): Nee
Intel® Quiet System Technology (QST): Nee
Intel® Quick Resume Technology: Nee
Intel® Client Initiated Remote Access (CIRA) technology: Nee
Intel® AC'97 technology: Nee
Extended Life Program (XLP): Nee
Pakket afmeting: 25 x 35.5 mm
ARK ID: 84575
Status: Discontinued
FSB's ondersteund: N/A
Productfamilie: Intel Edison
Productserie: Intel Edison board
Introductiedatum: Q3'14
Gelijkstroom-invoer mogelijk: Nee
Vereist een processor met Intel Graphics Technology: Nee
Maximaal geheugen: 4 GB
Laatste wijziging: 63903513
Datum verwachte stopzetting: 06/16/2017
FireWire-ondersteuning: Nee
Geïntegreerde DSP-sensorhub: Ja
Microcontroller-frequentie: 100 MHz

Heb je hulp nodig?

Als je hulp nodig hebt met Intel Edison Breakout Board stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd Intel

Intel

Intel M10JNP2SB Handleiding

27 Augustus 2024
Intel

Intel AXXRMFBU2 Handleiding

18 Maart 2024
Intel

Intel MPI999LSGE1 Handleiding

15 Juni 2023
Intel

Intel SC5400 Handleiding

11 Juni 2023
Intel

Intel SCSADVBACKUP Handleiding

9 Juni 2023
Intel

Intel Joule 570x Developer Kit Handleiding

7 Juni 2023
Intel

Intel Edison Breakout Board Kit Handleiding

6 Juni 2023
Intel

Intel SCSBACKUP Handleiding

5 Juni 2023
Intel

Intel SR1400 Handleiding

5 Juni 2023
Intel

Intel Edison Kit for Arduino Handleiding

4 Juni 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

LG

LG L227WT Handleiding

26 Maart 2025
Gima

Gima 20824 Handleiding

26 Maart 2025
Futaba

Futaba LT2F3500XH Handleiding

26 Maart 2025
Futaba

Futaba FT2F2100B-V2 Handleiding

26 Maart 2025
Futaba

Futaba FT2F1700B-V2 Handleiding

26 Maart 2025
Festo

Festo NEBM-M23G15-EH-7.5-Q9N-S1LEG21 Handleiding

26 Maart 2025
Focal

Focal HILO V3 Handleiding

26 Maart 2025
Cubot

Cubot X70 Handleiding

26 Maart 2025
Corsair

Corsair Obsidian Series 500D RGB SE Handleiding

26 Maart 2025
Atosa

Atosa ATHOM-28 Handleiding

26 Maart 2025