Genelec 8351AWM Handleiding

Genelec Speaker 8351AWM

Lees hieronder de 📖 handleiding in het Nederlandse voor Genelec 8351AWM (12 pagina's) in de categorie Speaker. Deze handleiding was nuttig voor 38 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/12

8260A, 8351A, 8250A and 8240A

Operating Manual

Introduction

Congratulations and a thank-you for the purchase of this Genel-

ec SAM system. All Genelec SAM systems are designed to in-

tegrate easily into the digital production environment. There are

several ways to configure and operate SAM systems for a wide

variety of high quality audio applications. The SAM monitors

also have analog inputs, making them versatile and intelligent

replacements for standard analog monitors.

This manual addresses the setup and use of the 8240A, 8250A,

8351A and 8260A SAM monitors in stand-alone mode without

the Genelec Loudspeaker Manager GLM™ and the proprietary

Genelec monitor control network. Use with the GLM™ is de-

scribed in the GLM™ System Operating Manual.

System

Genelec 8240A, 8250A, 8351A and 8260A are designed for

precise monitoring of 24 bit/192 kHz AES/EBU digital audio sig-

nal or line level analog audio signal. They are fully compatible

with Genelec Loudspeaker Manager GLM™ and the proprietary

Genelec monitor control network, and Genelec 7260A, 7270A

and 7271A SAM Subwoofers, but can also be used indepen-

dently of these. The 8240A, 8250A, 8351A and 8260A feature

high SPL output, low colouration and broad bandwidth in a small

enclosure size. They are suitable for a wide variety of tasks,

such as near field monitoring, mobile vans, broadcast and TV

control rooms, multichannel sound systems and home studios.

The Minimum Diffraction Enclosure™ (MDE™), advanced Di-

rectivity Control Waveguide™ (DCW™) and Minimum Diffrac-

tion Coaxial (MDC™) technologies provide excellent frequency

balance even in difficult acoustic environments.

Amplifiers

The amplifier unit is mounted in the rear of the monitor enclosure.

The unit incorporates special circuitry for driver thermal overload

protection. Variable input sensitivity allows accurate level match-

ing to console output section.

Setting Up the GLM™ Control Network

Although the

8240A, 8250A, 8351A and 8260A can be used

without the GLM

™ software and control network, they only reach

their full potential when set up and calibrated using the GLM™

software. The setup is fast and consists of the following steps:

1. Run a CAT5 (RJ45) cable from the monitor control network

to the next monitor (see Figure 1).

2. Run the final cable to control network input of the GLM

Adapter device.

3. Connect the GLM Adapter device to your computer USB

connector. The cable

is a part of the GLM User Kit

4. Place the Genelec measurement microphone at the listen-

ing location of the engineer, on a stand, with the microphone

pointing upwards and the microphone top at the height of the

engineers ear in normal working position. The microphone is

a part of the GLM User Kit.

5. Run the microphone cable to the microphone input in the

GLM Adapter device.

6. Download GLM software at the Genelec web site (www.

genelec.com). Install the GLM software.

7. Follow the GLM software instructions to measure and set

up your monitors.

8. If you plan to not use a computer for controlling the moni-

tors, use the GLM software to write the setting into the moni-

tors (“Store the Settings”).

Using the Monitors in Stand-Alone Mode

When the monitors are not connected to a Genelec monitor con-

trol network, they operate in the stand-alone mode. However, set-

tings made with the Genelec Loudspeaker Manager software can

be saved into each monitor and applied even when the network

is disconnected by setting switch 1 “STORED/MANUAL CON-

TROL” on switch group 2 of each monitor to position “STORED.”

All issues concerning use with the network are explained in detail

in the System Operating Manual provided with the GLM™ Loud-

speaker Manager software kit.

Connections

Each monitor is supplied with a mains cable, one 5 m GLM net-

work cable and an operating manual. Before connecting up, en-

sure that the mains switch is off.

LISTENING

POSITION

MICROPHONE

GLM

NETWORK

GLM

NETWORK

GLM

NETWORK

USB

Figure 1. GLM control network cabling

“MAINS INPUT” Connector

Connect the mains supply to this connector.

“DIGITAL IN AES/EBU” Connector

Use this female XLR connector for AES/EBU formatted digital

audio input signals. This input is selected automatically when a

valid digital audio signal is present, and overrides the analog in-

put.

Depending on the digital hardware, transmission of a 192 kHz

sample rate is achieved using a double speed, single channel/

cable interface. This is called dual-wire mode. In this case one

cable per channel is used and no channel selection is required.

Dual-wire mode is automatically detected by the input stage.

If the digital source device has a volume fader that controls the

digital level, it may be advantageous to lower the level control

either on the computer interface or on the monitor’s back panel

controls, which in turn will force the use of more of the digital [bit]

resolution in the volume control.

If the digital inputs are used, all audio outputs are referenced to 0

dBFS (digital Full Scale, the largest level that may be represent-

ed in the AES/EBU signal). These monitors produce 100 dB SPL

at 1 meter in free space for a digital input signal of –30 dB FS.

“DIGITAL THRU AES/EBU” Connector

This male XLR carries an unaltered copy of the digital signal fed

into the “DIGITAL IN AES/EBU” connector. It can be used for

daisy-chaining up to four monitors together.

“ANALOG IN” Connector

Use this connector for analog audio signals. The maximum input

level is +7.0 dBu RMS on models 8240A and 8250A and +22.0

dBu RMS on models 8351A and 8260A. When A/D converter

input clip occurs the front panel light turns momentarily red, indi-

cating the overload condition.

“CONTROL NETWORK” Connectors

Use these RJ-45 sockets to connect the monitor to the propri-

etary Genelec Loudspeaker Manager™ (GLM™) network only.

This connector is not Ethernet LAN compatible. Do not connect

to Ethernet LAN.

“12 V REMOTE” Connector (8260A only)

You can set up remote controlled powering up and down of the

8260A with 12 V voltage connected to this connector. The mini-

mum current needed to actuate this function is 70 mA.

Front Panel Warning Light

Normally the light on the front panel of a SAM monitor is green,

indicating that the monitor is in normal operational mode.

The overload light (red) is activated by several events:

• exceeding the maximum input range of the analog input

• the digital input level is less than 0.1 dB from the digital full

scale

• exceeding the output capacity of the power amplifier

(clipping in the power amplifier) and thermal

overload of the power amplifier or drivers (thermal

protection has activated)

• an error is detected in the AES/EBU audio data

If a red warning light appears, turn the analog source down! If

the levels are already modest and a digital signal is being used,

Figure 2. Connectors and controls on the back panel of a 8260A. The 8351A is similar. 8240A and 8250A share the same

layout but without the 12 V trigger voltage connector.

-2

-4

-8

-6

-12 0

-10

SWITCH

MANUAL

CT RL

-4 dB

160 Hz ON + O N

OFF + O FF

-6 dB -6 dB -2 dB

ST OREDDESKT OP

-2 dB -4 dB

BASS

ROLL-OFF

BASS

T ILT

-2 dB -4 dB +2 dB -4 dB

T REBLE

T ILT

OFF

SYST EM LVL.AES/EBU CH.

A B WF COAX

DRIVERMUT E SWITCH

-10 -20

-30

SU AND BM A

MADE IN FINLAND

8260A DSP TRI-AMPLIFIED

MONITORING SYSTEM

MAGNETICALLYSHIELDED

SERIAL NUMBER

MAINS INPUT 230 V~

50 / 60 Hz 330 W

DIGITAL IN

AES/EBU

www.genelec.com

29 822- 6 0T -6

ANALOG

DIGI L THRUTA

AES/EBU

12 V

REMOTE

OFF

Stand-alone user

interface level control

Stand-alone user

interface switch

groups 1 and 2

GLM Control

Network

connectors

Mains power

switch

Mains input

connector

Analog input connector

Digital Thru connector

Digital input connector

12V Remote

connector

(8260A only)

Product specificaties

Merk:	Genelec
Categorie:	Speaker
Model:	8351AWM
Kleur van het product:	Wit
Gewicht:	19000 g
Breedte:	287 mm
Diepte:	278 mm
Hoogte:	452 mm
Gebruikershandleiding:	Ja
Connectiviteitstechnologie:	Bedraad
Gemiddeld vermogen:	270 W
Aanbevolen gebruik:	Studio
Audio-uitgangskanalen:	1.0 kanalen
Speaker plaatsing:	Floor, Tabletop/bookshelf
Aantal drivers:	1
Woofer:	Ja
Frequentiebereik:	32 - 35000 Hz
Gevoeligheid:	111 dB
Versterker:	Ingebouwd
Diameter woofer:	8.5 "
Diameter hogetonenluidspreker:	0.75 "
Diameter mid-range driver:	101 mm
XLR in:	Ja
Tweeter:	Ja