Exakta Exa Handleiding

Exakta Fotocamera Exa

Lees hieronder de 📖 handleiding in het Nederlandse voor Exakta Exa (42 pagina's) in de categorie Fotocamera. Deze handleiding was nuttig voor 59 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/42
1
[Translated from the German Ihagee manual with the aid of QuickDic 7.2
(www.quickdic.de
)
. Notes in square brackets are mine – Steve Sheppard.]
2
EXA, EXA I Repair Manual.
Basic Remarks:
The camera under repair is placed with the lens mount 350.09 to the front, i.e. in the photograph
taking direction.
EXA
Right: Side with wind knob 350.07-23.
Left: Side with time setting lever 350.04 U 3.
EXA I/63
Right: Side with wind knob 350.17-24.
Left: Side with time setting disc 350.21 U 3.
All screws and nuts have right-hand threads. Never use force!
Before every repair remove the viewnder (Do not touch the ground-glass screen).
A. Disassembly of EXA camera.
1. Remove the back 350.02
a) Withdraw the take-up spool 350.10.
2. Right side open.
a) Slacken the grub-screw in the wind knob 350.07-23, and withdraw the wind knob upwards.
b) Remove the two top-plate screws M1.2 DIN 91, take o the right top-plate 350.01-7, and
the rewind release button 350.01-6.
c) Ret the wind-knob. The grub-screw must be rmly tightened on the milled face of the
spindle. Take notice of the ratchet pawl 350.07-22 for the frame counter.
3. Left side open.
(This disassembly is not necessary to dismantle the inner parts.)
a) Remove the two top-plate screws M1.2 DIN 91.
b) Slacken the grub-screw in the wind knob 350.07-23, and withdraw the wind knob upwards.
Withdraw the rewind spindle 350.12-6 from below.
c) Take o the left top-plate 350.03-7.
d) Ret the rewind knob. Tighten the grub-screw rmly on to the milled face of the rewind
spindle.
4. Mechanism removal.
a) Cock the shutter.
b) Place the camera front upwards.
c) Remove the four xing screws M1.7 x 6.5 DIN 91 from the lens ange 350.09, and remove
the ange (noting any shims 300.21-52/1).
d) Remove the shutter inhibit lever 300.21-46, the screws M1.2 for the front-plate, and the
front-plate 350.11 U1 (or 350.11 U3).
3
e) Remove the xing screw M1.7 x 4 DIN 63 for the inner mechanism (in the milled area for
the lens ange).
f) Place the camera back side uppermost.
g) Remove the inner-mechanism xing screws M1.7 x 4 DIN 85 in both cassette chambers.
h) Place the camera upright.
i) Remove drive-pinion 350.01-9 from sprocket spindle 350.01-4.
j) Set shutter speed lever 350.04 U 3 to B, and extract the inner mechanism from the outer
housing. Do not touch the mirror.
AA. Disassembly of EXA 1/63 camera.
1. Remove the back 370.20.
a) Withdraw the take-up spool 370.09.
2. Removal of top-plate 350.21 U1.
a) Remove screw 350.21-24, bush 350.17-25 for frame-counter disc, frame-counter disc
350.17 U5, and spring-washer 350.17-27. Withdraw wind knob 350.17-24, pushing against
the end of the wind bush 350.17 U4 with two ats [Zweikant].
b) Withdraw the spool-retaining spring 300.15 U 12 from the rewind bush. Unscrew the
rewind bush [remove the screw] (pay attention to compression-spring 350.21-29, shim
beneath 300.15-34, and distance piece 370.21-21), and pull out the rewind spindle 350.21-
20 with rewind-knob 350.21-19.
c) Release circlip 6 DIN 6799, remove spring-washer 370.04-45, and take o time-setting disc
350.21 U 3.
d) Remove the four top-plate xing screws M1.4 x 3 DIN 91, and take o the top-plate.
e) Ret the time-setting disc with spring-washer and circlip (pay attention to the contact disc
350.22-13 and setting slide on time plate 350.22-U1)[i.e. make sure the pin on time setting
disc engages with the paxolin disc and the sliding plate for speed setting below].
f) Ret the wind-knob, spring-washer and frame-counter disc with sleeve and screw (pay
attention to rewind latch 350.17-19).
3. Mechanism removal.
a) Cock the shutter.
b) Place the camera front side upwards.
c) Remove the four xing screws M1.7 x 6 DIN 63 for the lens-ange 350.09, and take o the
lens-ange (noting any shims 300.21-52/1).
d) Remove the mechanism xing screw M1.7 x 4 DIN 63 (in the milled area for the lens
ange).
e) Place the camera with the back side upwards.
f) Remove the inner mechanism xing screws M1.7 x 4 DIN 84 in both cassette chambers.
g) Extract the inner mechanism from the outer housing. Do not touch the mirror.
B. EXA assembly.
1. Mechanism insertion.
As under disassembly of camera A.4, but in reverse order. Check for correct functioning.
2. Close left side.
As under disassembly of camera A.3, but in reverse order. Check for correct functioning.

Product specificaties

Merk: Exakta
Categorie: Fotocamera
Model: Exa

Heb je hulp nodig?

Als je hulp nodig hebt met Exakta Exa stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Fotocamera Exakta

Exakta

Exakta A Handleiding

8 Februari 2024
Exakta

Exakta Exa Handleiding

16 Februari 2023
Exakta

Exakta Kine-Exacta Handleiding

16 Februari 2023

Handleiding Fotocamera

Nieuwste handleidingen voor Fotocamera

Kodak

Kodak Ektar H35N Handleiding

14 December 2024
Kodak

Kodak Step Touch Handleiding

14 December 2024
Kodak

Kodak Advantix 3600ix Handleiding

14 December 2024
Kodak

Kodak EasyShare C360 Zoom Handleiding

14 December 2024
Kodak

Kodak EasyShare Z8612 IS Handleiding

14 December 2024
Imou

Imou Ranger Dual 10MP Handleiding

14 December 2024
Imou

Imou Ranger Dual 8MP Handleiding

14 December 2024
Imou

Imou Ranger Dual 6MP Handleiding

14 December 2024
Fujifilm

Fujifilm Intax Wide 300 Handleiding

14 December 2024
Fujifilm

Fujifilm Intax Mini Hello Kitty Handleiding

14 December 2024