Electro Harmonix Deep Freeze Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Electro Harmonix Deep Freeze (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 45 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4
DEEP
FREEZE
User Manual
Sound Retainer
Welcome to the Electro-Harmonix Deep Freeze Sound
Retainer. With the simple push of a button, the Deep Freeze
allows you to sustain individual notes and chords indefinitely,
gliss between frozen sounds, layer sounds and notes, and
automatically freeze notes or chords as you play. All of this
in an extremely compact, pedalboard-friendly package!
Operating Instructions
Insert the output plug from the supplied 9VDC AC adapter
into the power jack at the top of the Deep Freeze. The unit
must be powered to pass signal, even in bypass. The Deep
Freeze features buffered analog bypass or digital bypass
depending on settings. Connect an instrument cable from
your instrument to the Input jack. Connect an instrument
cable between the Output jack and a suitable amplifier.
As a starting point, set the DRY and EFFECT knobs to 50%
and the SPEED/LAYER and GLISS knobs to minimum.
Controls & Jacks
1. MODE Button Selects how the footswitch controls the effect.
LATCH (Green LED) Play a note or chord and then press
and release the footswitch to activate the effect and light
the LED green. After you release the footswitch, the effect
remains active and your sound sustains indefinitely. Dou-
8
9
2 3
1
6
6
4 5
7
DRY EFFECT
MODE
GLISS
SPEED
LAYER
Power Suppy Requirements: Voltage: 9VDC Current: 100mA Polarity: Center-Negative
This device comes equipped with an Electro-Harmonix 9.6DC-200 power supply. Use of the wrong adapter or a
plug with the wrong polarity may damage the device and void the warranty. Do not exceed 10.5VDC on the power
plug. Power supplies rated for less than 100mA may cause the device to act unreliably.
ble-tap the footswitch to end the frozen sound and
enter bypass. Each time you press down on the
footswitch, the sound present at the Input jack is
frozen. The SPEED/LAYER knob allows you to layer
frozen sounds. The setting of the knob—at the
moment you press the footswitch—sets the volume
level of previous layers. Turn down SPEED/LAYER
to minimum to disable layering; set to max to allow
frozen layers to remain at full volume.
MOMENT MODE (Orange) Play a note or chord
and then press and hold the footswitch to activate
the effect and light the LED. The freeze effect
sustains indefinitely while you hold down the
footswitch. Release the footswitch and the Deep
Freeze enters bypass.
AUTO MODE (Red) The Deep Freeze detects each
new note or chord you play and freezes it automat-
ically. Press the footswitch to engage the effect and
light the LED red. Double-tap the footswitch to return
to bypass. The SPEED knob sets the fade-out time
of the auto freeze. When SPEED is set to maximum,
the sustained notes do not fade out. While Auto is
engaged, press and hold the footswitch to stop
accepting new notes and sustain the freeze indefi-
nitely, allowing you to play over the frozen sound.
2. DRY Controls the output level of the dry signal.
3. EFFECT Controls the output level of the effect.
4. SPEED/LAYER In LATCH mode, this knob controls
how much of the previously frozen sound is layered
onto your new freeze. In MOMENT mode, this knob
controls how quickly the frozen signal fades in and
out. In AUTO mode, by default, this knob controls the
fade-out time of the frozen sounds after you play a
new note/chord. This can be changed to affect the
attack instead of the decay of the signal, see the
Auto Decay & Attack Modes section for more.
5. GLISS This knob adjusts the speed of the gliss
effect. Gliss morphs one frozen note or chord into
the next; it is similar to the portamento function
found on many synthesizers. As you turn the GLISS
knob clockwise, the gliss time increases. To turn
gliss off completely, turn the GLISS knob down all
the way to its full counterclockwise position.
PERFORMANCE NOTE: The easiest way to hear the gliss
effect is to put the Deep Freeze into AUTO mode, com-
pletely turn down the DRY knob and set the GLISS and
SPEED/LAYER knobs to 50% or higher.
6. Footswitch and Status LED Footswitch engages
or bypasses the effect. The LED color indicates the
selected mode. In bypass mode, the LED is off.
7. Input Jack Impedance: 2.2MΩ, Max In: +1.5 dBu
8. Output Jack Impedance: 680Ω, Max Out: +2.1 dBu
9. Power Jack Current draw: 100mA at 9.0VDC


Product specificaties

Merk: Electro Harmonix
Categorie: Niet gecategoriseerd
Model: Deep Freeze

Heb je hulp nodig?

Als je hulp nodig hebt met Electro Harmonix Deep Freeze stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Electro Harmonix

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd